Answer Posted / sanat ullah khan

Answer
# 1 it depond upon the output load

Thanks for Marking this Answer 0 Krish
Answer
# 2 its depend on current of the load which connected to
the battery amphere per hour if a battery having 10AH it
can give 10A load upto a hour

Thanks for Marking this Answer 0 Karthik Raman.b
Answer
# 3 Hi Krishna,

V HV AN 65AH 32 No's of Batteries connected 60kva UPS,

What will be the full load backup time???

Thanks for Marking this Answer
Answer
# 4 First you must know the ampere-hour of your battery
bank as
per the manufacture's specification.Now discharge the
batteries as per the C5 rating( for Ni-Cd batteries) or C10
rating (for Lead -acid Batteries).Discharging can be done
by connecting the positive and negative terminals of
batteries to the copper plates and immersing in a salt
solution, which will act as a load. The distance between
the plates can be adjusted to set the discharge current.
Measure the amount of discharge current and time till the
battery voltage of each battery in a bank drops to 1 Volt
if it is a 1.4 volt cell. Now multiply the discharge
current and time. This is the measure of the Amperehour
capacity of the bank.If the Amppere -hour capacity as per
the manufacture is available then you can determine the
percentage capacity of your bank at present.Remember that
charging and discharging of battery bank improves the
health of the battery bank.However, for lead -acid
batteries these cycles are around 750 or say 3 years. For
Ni-Cd batteries the life is around 25years or more if
maintained properly.Selecting a overated battery is also
not adviseable as it won't get discharged completely and
this may result in sulfation of batteries and early death
of battery bank.

Thanks for Marking this Answer 0 Avinash

1 “earthing” for bonding of equipment and circuits to common plant earth electrode potential, 2 “protective earthing (PE)” when this bonding is required for personal safety provisions 3 “grounding” for interference suppressing bonding of screens, sys-tems with ground level 4. low-impedance earthing ? 5.primary earthing system and secondary earthing system what is that? 6.earthing electrode or mesh net earthing electrode ? very confusing , simple but very informative help required ? i will be very very thankful to you guys.

1588

---

How much no load current of synchronous motor

1582

---

WHAT IS THE TECHNICAL SPECIFICATION OF C CURVE & D CURVE LEGRAND MAKE MCB

2068

---

what r PID controllers?why they r used?what is there purpose?plz Explain in detail

1608

---

what material is used in capaciter

1461

---

---

Explain the laying procedure and laying depth of submarine/subsea power cable for 220/400KV system? Also available cable diameter?

1675

---

What is genrally the % Impedance of a Dg set? How can we calculate Earthing conductor size for a DG set?

3407

---

Classify drilling machines.

672

---

How much kv gas generator is needed to run 2 hp and 1 hp airconditioners, plus a refrigerator and 4 Tvs

4381

---

I have an existing old MCCB. ABB Model SACE, the rating are: Ue = 660 volts, Iu =1250 Amps, 3 poles, Ith (max) =800 amps at 45 deg C. I need a circuit breaker for my 3 phase motors, 380 volts 60 hz. the supplier required the minimum ampacity of the breaker to be 911 amps. can i use this breaker with rating of Iu =1250 amps but Ith = 800amps maximum?

1766

---

what are the tests comes under the type test, what tests comes under routine tests.

1019

---

what is difference between speed mode and torque mode in motor?? explain in simple words please.

1138

---

Define ampere

698

---

What is proportional controller?

682

---

the winding of Generator and Motor is star or in delta ? and why

627

---