Interested to Buy Any Domain ? << Click Here >> for more details...
To find closed tank level by DP transmitter , how to
findout its range.and insomeplace they using range like -
1500 to +1500 mmwc why not 0 to 3000 mmwc. how they spilit
they range for minus and plus.and why?
- 1 Answers
- 10140 Views
- Kuwait Oil Company, I also Faced
- E-Mail Answers
Answer Posted / yashwant
THIS IS LEVEL MEASUREMENT USING DP TRANSMITTER, CLOSE TANK
MEANS PRESSURIZED ,PRESSURE IS EVERY WHERE IN SIDE TANK WILL
BE SAME. LOW SIDE WILL BE TOP SIDE WHERE ALL CONDENSATE
COLLECTED THIS IS REFERENCE SIDE, NOW ON OTHER HAND HIGH
SIDE WILL BE LOWER, DIFFERENTIAL PRESSURE OBSERVED AT DPT.
LOWER SIDE WILL BE ALWAYS FULL IE FULL SCALE IF YOU ARE
HAVING TANK HEIGHT 1500 MM THEN PRESSURE AT LOWER SIDE IS
1500 MMWC. AND THAT OF HIGHER SIDE WILL BE THE ACTUAL WATER
INSIDE TANK WE SAY 500 MMWC STEAM PRESSURE WILL BE EVERY
WHERE SAME SO NO NEED TO CONSIDER PRESSURE INSIDE THE TANK.
MINUS AND PLUS WILL BE JUST FOR HAVING DIFFERENCE IN TWO
COLUMN IE HP AND LP. ALSO TANK IS NOT PRESSURIZED YOU CAN
USE PRESSURE TRANSMITTER CALIBRATED IN YOUR RANGE (HEIGHT OF
TANK MMWC)
| Is This Answer Correct ? | 6 Yes | 4 No |
Post New Answer View All Answers
Please asked me How calculate DCS controller memory.
key phaser where is use and work
any questions on motor and energy conversions machines?
how to work static pressure sensore how to work dpt
Please tell me details about Sox,Nox,SWAS analyser????
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
what does the ratio 800-400-300-200/1-1-1-1-1 in the specification of current transformer indicates?
what is intrinscily safe system and where we use?
Which language of programing is popular? how can i learn it ?
How u will setup SPI(2007) on Citrix Server (Thin Client Mode)? Plz Justify?
State four different types of flow measurement, for gas flow measurement MMSCFD is the common unit expand the unit and specify significance of word S in the unit.
Which type of diagphram use in costic line,DM water line,natural gas line,oil line?
Draw a simple circuit for a well head control panel used to protect the well against fire, leak, blockage, ESD, & controls the operation of one downhole & one surface safety valve. Explain the operation and controls
What are the different types of thermistors used in industries? How to the operation of typical thermistor?
What is the difference between modbus,fieldbus & profibus
