1)What is Suggested type of cement for concreting at water,
for mass concreting and where the chaces of gettin attucked
by salt?
2)How many types of camber?
3)why we always preffer short column in case of residential
building?
4) Is there any advantages between the use of One way slab
& two way slab?
5)What shoul be the % of steel for R. C. C. perpose based
on volume & area ?
- 7 Answers
- 12404 Views
- Gammon, I also Faced
- E-Mail Answers
Answer Posted / sjtbehera
Ans1. In marine structure M20 is used in PCC and M30 &
above is used in RCC
Ans2. I think camber which are provided in Road are three
type
1. Parabolic
2. Straight line
3. Combination of parabolic and straight
4.
Ans3. The short columns are fail by only crushing where as
long column fails by buckling action.
Ans4. One way slab & two way slab are design according to
their need. One way slab are used when ratio of length of
the room to its width is greater than 2. such slad are
designed to span along width of the room. Main
reinforcement along width of room and carried load and
distributions are right angled to main reinforcement.
In two way slab is used where length of room to
breadth is less than 2 . in this case reinforcement are
provided in both length and breadth of room.
Ans5. in the case of building % steel in the base of rcc
are used in following manner
1. footing – 6%
2. beam- 1 %
3. column – 1.2%
4. lintel- .6%
5. slab- .8%
6. staircase- .8%
| Is This Answer Correct ? | 12 Yes | 3 No |
Post New Answer View All Answers
You have 3 snd sample of different FM=0.21,FM=0.95,FM=2.90 which one is suitable for a)plastering on R.C.C b)plastering on masonary wall c)concreting column d)concreting of bored pile.also justify your answer.
What is binding spacing of the rebars at lapping zones.
What is unit weight of roadway layer.. 1.bitumen 2.sand 3.soil 4.concrete 5. aggregate give me some reference for this answers
What is dead load impact load live load
1) a)to prepare mortar for bricklaying how much amount of water should be added for its maximum strength and workability(to avoid cracks which results, when high quantity of water is added)?is their a formula or ratio? b) suppose we want to make 1:3 mortar,what is the best way to measure cement ,sand and water and how? c)time before which freshly prepared mortar should be used? d)proper way to mix and make mortar? e)when should curing start after laying bricks and for how long?and also how many hours per day? f)what is shear wall (please in terms of layman lol) bookish definisions are confusing.... g) and last,acc to codes what are max no. of course that should be laid in a day.
What is need for setting limits?
What is the Roll of Water Bonding under VDF road?
In Rcc ratio calculation I wanted to know quantity of Steel also.
TO CONSTRUCT A 1800 SQFT CAPACITY UNDERGROUND WATER TANK HOW MUCH CUFT CONCRETE IS REQUIRED AND HOW MUCH REINFORCEMENT IS REQUIRED. FOR COSTING
How to arrive the co- efficient of all civil activities? For ex:- painting-enamel in wooden doors. co efficient is 1.8. How this is calculated
what will happen if one could not properly follow the spacing of slab reinforcement bar?
A sieve analysis results in 100% retained in no. 50 Sieve, the fm is?
i need the syllabus for the direcr recruitement of executive engineers in andhrapradesh
Write short note on construction programme for pile foundation.
How Can I know the wastages(%) of each work added in estimating the quantity of construction materials?(Eg. Ceiling Work, Brick Work,etc....)
