What is the difference between Isolator annd Circuit
Breaker.
- 21 Answers
- 72088 Views
- ABB, Lanco, NTPC, Power Grid, RInfra, I also Faced
- E-Mail Answers
Answer Posted / senthil kumar
isolator is a off load device ie we cant able to close the
isolator under onload condition if we close the isolator
under onload it will damage the isolator but breaker is a
device having high withstand capacity(the withstand
capacity is based on application)so we can able to open
&close the breaker under both onload &offload
conditions......and also while opening &closing under
onload arc will appears at the contacts. the isolator have
no special arrangement to extinguish that arc but in
breaker we have some special arrangement to extinguish that
arc.
| Is This Answer Correct ? | 42 Yes | 11 No |
Post New Answer View All Answers
how to calculate the magnetizing current of ct ( 800A/1A) for Relay 64
What the formula for calculating no.of earthings & size of earth strip for 100mX90m shop.
there is an alternator 480 k.w, 400v,50hz, 4-wire running on load having leakage alternator body earthed current 38 A. is it within acceptable limit? if yes then give reference if no then how to bring within specified limit
Percentage losses in power generation?
hi everybody how to design string combiner box (scb) internal parameters like bus bar and spd (surge protection device and fuse which place to set that,and also bus bar one particular cross sectional how much heat generated and how much power loss tell me Clearly and briefly
can anyone tell me can the electromagnetic waves can be reflected back?if so how &by which material it can be reflected back?please tell me so that it can help to my wireless power trasnmission device.
Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1. H1-H2 = H2-H3 H3-H1 2. H2-H3 = H3-H1 H1-H2 3. H3-H1 = H1-H2 H2-H3 For the LV side also: 4. X1-X0 = X2-X0 X3-X0 5. X2-X0 = X3-X0 X1-X0 6. X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0 H2-H0 H3-H0 X0-X1 X0-X2 X0-X3 128.0 119.9 7.2 29.2 13.3 15.8 70.7 128.4 59.2 23.4 22.0 3.6 7.2 120.1 128.1 13.4 29.3 15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?
In Plumbing services What are accessories we consider for a bathroom?
armature is that part in which current is induced since in dc motor we supply current to the conductor so why we call it armature?
i am going to correct power factor of 1600kw induction motor,when i calculate capacitance of capacitor it is three time more in star connection than delta. if motor is star connected which connection i shall adopt for capacitors and reason for adopt this connection
please suggest some good universities with low cost iam in totally full confusion so please help me my profile gre 283 and ielts 5.5
hi frnds what is meant by harmonics & what is meant by third hormonics,where its will occur ?thank u
I WANT TO know WHICH WAY IS BETTER FOR CONNECTION BETWEEN POWER TRANSFORMER AND MAIN DISTRIBUTION PANEL. 1-IS BETTER WE USE CABLE? 2-IS BETTER WE USE BUS DUCT? my transformer rate power is 2500KVA
how to calculate the conductor size for certain KV transmission line and distribution line?
What is true sine wave or pure sine wave inverter?? Is it sine wave or step wave?? If it is step wave, waves with how much step is considered as pure sine wave? Is it possible to produce pure sinewave using power electronics?
