Answer Posted / rajashekar @ nitt

give input at base and connect resistor at collector and
gnd at emitter,vcc at collector finaaly take output at
collector.

Need to convert this VHDL code into VLSI verilog code? LIBRARY IEEE; USE IEEE.STD_LOGIC_1164.ALL; ----using all functions of specific package--- ENTITY tollbooth2 IS PORT (Clock,car_s,RE : IN STD_LOGIC; coin_s : IN STD_LOGIC_VECTOR(1 DOWNTO 0); r_light,g_light,alarm : OUT STD_LOGIC); END tollbooth2; ARCHITECTURE Behav OF tollbooth2 IS TYPE state_type IS (NO_CAR,GOTZERO,GOTFIV,GOTTEN,GOTFIF,GOTTWEN,CAR_PAID,CHEATE D); ------GOTZERO = PAID $0.00--------- ------GOTFIV = PAID $0.05---------- ------GOTTEN = PAID $0.10---------- ------GOTFIF = PAID $0.15---------- ------GOTTWEN = PAID $0.20--------- SIGNAL present_state,next_state : state_type; BEGIN -----Next state is identified using present state,car & coin sensors------ PROCESS(present_state,car_s,coin_s) BEGIN CASE present_state IS WHEN NO_CAR => IF (car_s = '1') THEN next_state <= GOTZERO; ELSE next_state <= NO_CAR; END IF; WHEN GOTZERO => IF (car_s ='0') THEN next_state <= CHEATED; ELSIF (coin_s = "00") THEN next_state <= GOTZERO; ELSIF (coin_s = "01") THEN next_state <= GOTFIV; ELSIF (coin_s ="10") THEN next_state <= GOTTEN; END IF; WHEN GOTFIV=> IF (car_s ='0') THEN next_state <= CHEATED; ELSIF (coin_s = "00") THEN next_state <= GOTFIV; ELSIF (coin_s = "01") THEN next_state <= GOTTEN; ELSIF (coin_s <= "10") THEN next_state <= GOTFIV; END IF; WHEN GOTTEN => IF (car_s ='0') THEN next_state <= CHEATED; ELSIF (coin_s ="00") THEN next_state <= GOTTEN; ELSIF (coin_s="01") THEN next_state <= GOTFIV; ELSIF (coin_s="10") THEN next_state <= GOTTWEN; END IF; WHEN GOTFIF => IF (car_s ='0') THEN next_state <= CHEATED; ELSIF (coin_s = "00") THEN next_state <= GOTFIF; ELSIF (coin_s ="01") THEN next_state <= GOTTWEN; ELSIF (coin_s = "10") THEN next_state <= GOTTWEN; END IF; WHEN GOTTWEN => next_state <= CAR_PAID; WHEN CAR_PAID => IF (car_s = '0') THEN next_state <= NO_CAR; ELSE next_state<= CAR_PAID; END IF; WHEN CHEATED => IF (car_s = '1') THEN next_state <= GOTZERO; ELSE next_state <= CHEATED; END IF; END CASE; END PROCESS;-----End of Process 1 -------PROCESS 2 for STATE REGISTER CLOCKING-------- PROCESS(Clock,RE) BEGIN IF RE = '1' THEN present_state <= GOTZERO; ----When the clock changes from low to high,the state of the system ----stored in next_state becomes the present state----- ELSIF Clock'EVENT AND Clock ='1' THEN present_state <= next_state; END IF; END PROCESS;-----End of Process 2------- --------------------------------------------------------- -----Conditional signal assignment statements---------- r_light <= '0' WHEN present_state = CAR_PAID ELSE '1'; g_light <= '1' WHEN present_state = CAR_PAID ELSE '0'; alarm <= '1' WHEN present_state = CHEATED ELSE '0'; END Behav;

5272

---

What is Noise Margin? Explain the procedure to determine Noise Margin?

2456

---

What is the difference between cmos and bipolar technologies?

1129

---

Draw Vds-Ids curve for a MOSFET. Now, show how this curve changes with increasing Vgs.

1111

---

Explain about 6-T XOR gate?

1268

---

What are the various regions of operation of mosfet? How are those regions used?

1134

---

Give the cross-sectional diagram of the cmos.

995

---

Design an 8 is to 3 encoder using 4 is to encoder?

1329

---

What does the above code synthesize to?

2596

---

What are the steps involved in designing an optimal pad ring?

1170

---

In vlsi chip 1000s of transistors are dropped, specifically categorized. Which method is used to achieve this & how it is done practically?

1017

---

What are the steps required to solve setup and hold violations in vlsi?

1088

---

What types of I/O have you designed? What were their size? Speed? Configuration? Voltage requirements?

2437

---

What work have you done on full chip Clock and Power distribution? What process technology and budgets were used?

3267

---

why is the number of gate inputs to CMOS gates usually limited to four?

1340

---