if 10 pc's connected from internet, in 8 pc's internet is
correctly run but in other 2 pc's they can not access
internet,what's the problem?
Answers were Sorted based on User's Feedback
1)check the physical connection's at first
2) go to cmd and type ipconfig /all and check there the
default gatway is correct or not of that two pc's,,,,
and the mac address also we can check .if mac address not
display it mean the ehernet card is not working
properly,replace that.
if any other reason please suggest,
thankfully
Is This Answer Correct ? | 28 Yes | 5 No |
Answer / jitendera
Hey Guy
Being a Network Engineer donot think like System admin
If 8 pc are working and 2 pc are not working there are lots
of issue from switch side...
1) miss configuration of vlan interface might be switch
port are in different valn not allowed to access internet
2) switch port are in error-disable mode
3) access-list might be a issue
4) switch port are in shut mode
5) cable are Bad
6) Switch-port failed
7) and then you can think from system side
like nick card . misconfiguration of ip address or DNS and all
Is This Answer Correct ? | 18 Yes | 3 No |
i agreed with you (sr.no- 2 to 7)but jitendera tell me one
thing in 10 pc's if we took 10 to 15 port switch our
problem easily solve then why we create v-lan .
v-lan is required in very large organization.
may be some system's dhcp enable and some are statically
configured ,so this type problem may also occurred.
(Being a Network Engineer donot think like System admin
)--this question asked from me (Tata Telecom,pune)for
network admin profile.
Is This Answer Correct ? | 9 Yes | 2 No |
Answer / ankit
my personal learning is, we should always check the cause from the root, I totally agree with Adi, checking these basic steps can save valuable time.
Jitender your answer is also correct, but these are later steps to be taken.
Is This Answer Correct ? | 4 Yes | 0 No |
Answer / jitendera
Ok
here is the explanation Question has been asked that if 10
pc are able to access but 2 not so where it has been written
that think on small scale business
Why i have putted this one because it might be possible that
in a switch 10 port are in that vlan from where you can
access the intrnet
Example vlan 301 let gess it is for internet
so
config)# interface range 1 -12
switch port access mode access
switch port access vlan 301
now what ever device will connect to the port can access the
internet
now if on the same switch vlan 302 has been configured not
for the internet access
config)# interface range 13 -15
switch port access mode access
switch port access vlan 302
here what ever device is connected over it
Note that i am talking about Staic VLAns not Dynamic one
(may be some system's dhcp enable and some are statically
configured ,so this type problem may also occurred)
No not really if the entry are correct like ip address mask
gateways and DNS i am damm sure it will be accessible .. so
this is not at all is the issue
Is This Answer Correct ? | 5 Yes | 2 No |
Answer / sanjula
i agreed with the jitender because firstly we check the switch side
Is This Answer Correct ? | 3 Yes | 1 No |
Answer / asif rafiq
access to internet from
these two ip's are
restricted by the access
list commands if u have
learnt access list...
Is This Answer Correct ? | 0 Yes | 0 No |
What device has content-addressable memory (CAM) and what is stored in it? 1 A: Switch, learned IP addresses 2 B: Router, learned IP addresses 3 C: Switch, learned MAC addresses 4 D: Router, learned MAC addresses
How loops are introduced in switching? Whats the solution for that.
When would you use ISDN? A.) To connect LANs using POTS B.) To support applications requiring voice, data, and video C.) When you need a consistent and very high rate of data speed D.) To connect to IBM mainframes
Identify the 4 that are WAN technologies? A.) HDLC B.) FDDI C.) 802.5 D.) HSSI E.) SDLC F.) Frame Relay
How does the cut-through switching technique work? A.) By using broadcast address as source addresses B.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets C.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface D.) By using a Class I repeater in a collision domain
How do you go to privileged mode? How do you switch back to user mode?
What is the difference between RIP & RIPng???? Can anyone explain it..!!! Thank u in advance.
Which type for communication switch do?
To prevent Service Advertisements (SAPs) from flooding a network, Cisco routers do not forward them. How are services advertised to other networks? A. Each router builds its own SAP table and forwards that every 60 seconds. B. Each router assigns a service number and broadcasts that. C. SAPs aren't necessary with Cisco routers. D. Cisco routers filter out all SAPs.
Explain the difference between arp and rarp?
friends i have 3ree prob which is asked in ibm india in technical round 1 what is ftp(this was easy i had answered) 2 why we use ftp(i think it is a tough one) 3 how can we enable ftp in the widows xp. friend i need these question answer as soon as possible if it is possible to reply within the eveing then i always obeyliged to you i am espacily looking towards the jitendera sinha who make most of the valuable answer loking toward you nidhi mall
Explain what is formula of hold down time of eigrp protocol?