Interested to Buy Any Domain ? << Click Here >> for more details...
Identify 2 characteristics of PPP?
A.) Uses LLC to establish the link
B.) Default serial encapsulation
C.) Support multiple layer 3 protocols
D.) Offers two types of authentication; PAP and CHAP
- 3 Answers
- 8067 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / samdani
c ans d are the answer. it use llc but now to establish
link but to control the link
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / robert
B & C.
1. Autentication use in ppp is EAP
2. For link establish it use LCP.
| Is This Answer Correct ? | 2 Yes | 5 No |
Mention what command you must use if you want to delete or remove the configuration data that is stored in the nvram?
Select the compression protocols for PPP? A. Stac B. Predictor C. Quality D. Magic Number
Select the correct statements about PPP and SLIP for WAN communications? A. PPP uses its Network Control Programs (NCPs) component to encapsulate multiple protocols. B. PPP can only transport TCP/IP C. SLIP can only transport TCP/IP. D. SLIP uses its Network Control Programs (NCPs) component to encapsulate multiple protocols.
A user device that connects to a DCE must be which of the following? A.) DTE B.) CPE C.) Demarc D.) DCE E.) CO
What are the steps of conversion for data encapsulation?
Identify the hardware component that stores the backup configuration? A.) RAM B.) NVRAM C.) Flash D.) ROM
Which of the following are valid WAN terms? A.) DTE B.) DCE C.) Demarc D.) CPE
Which statement is true regarding full duplex? A.) Allows for transmission and receiving of data simultaneously B.) Only works in a multipoint configuration C.) Does not affect the bandwidth D.) Allows for transmission and receiving of data but not a the same time
In Novell's use of RIP, there are two metrics used to make routing decisions. Select the two metrics. A. Ticks. B. Hops C. Loops D. Counts
Define topology?
3 router configured with RIP & Ripv2 rotuer 1- connected with router 2 having sr ip 10.0.1.2 routing : ripv2 router 2: connected with router 1 and router 3 having sr 0 ip 10.0.1.3 & sr 1 ip 11.0.1.2 routing :rip & ripv2 router 3: connected with router 2 having sr ip 11.0.1.3 routing: rip is there communication possible btween these networks ? if yes how
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
CCNA 
