Answer / jitendera

rip-distnece vector protocol

ospf-link state

eigrp -hybrid protol


rip- not supporte vlsm
ospf-support the vlsm
eigrp-support the vlsm

more diffrence

Answer / goutham

ospf - there is no limitation of hop count
eigrp - maximum we can use 255 hop count only
rip - maximum hop count is 0-15, but 16 is deemed
unreacheble.

Answer / hitendra suthar

RIPv1- Distance Vector, Classful routing, open standerd
RIPv2- Distance Vector, Classless routing, open standerd
EIGRP- Advance Distance Vector Distance Vector,Classless routing,cisco propriety
OSPF- Link state, classless routing, open standerd
RIPv1- use broadcast and maximum hop count 15, 16 unreachable
RIPv2- use periodic multicast 224.0.0.9 and maximum hop count 15, 16 unreachable.
EIGRP- use multicast on change 224.0.0.10 maximum 255 hops
OSPF- use multicast 224.0.0.5 and 224.0.0.6 supports large network.
RIPv1- No authentication and no AS(Autonomous System)no.
RIPv2- MD5 authentication and no AS no.
EIGRP- MD5 authentication and use AS no.
OSPF- MD5 authentication and use area.

Answer / vijay kumar

RIP- Send the complete routing table out to all active
interface(update time) every 30 sec..ad value 120.

EIGRP- Default hop count set 100, use Dual Algorithm..AD
Value (Administrative Value) 90..

OSPF- Ad value 110, Support DIJKSTRA Algorithm.

Answer / zeeshan

Ad value:
Rip-120
Eigrp:Internal-90
External-170
Ospf-110

Protocol:
Rip- distance vector
Eigrp- hybrid protocol
Ospf- link state

Hello timer:
Rip- 30sec
Eigrp- 5sec
Ospf- less than 1sec

Algorithm:
Rip- bellmen ford
Eigrp- dual method
Ospf- dijkstra

Updates:
Rip- sends full update
Eigrp- triggered update
Ospf- triggered and periodic update

Hop count:
Rip- 15
Eigrp- 255
Ospf- no limit

Support n/w:
Rip- smaller networks
Eigrp- large networks
Ospf- large enterprise networks

Vlsm support:
Rip- no
Eigrp- yes
Ospf- yes

Answer / ajay

rip is perodicly and both are non perodicly

Answer / nilesh bhosle

rip is twor version
1) class full :- it's not update the routing table to all
active interface
2) class less :- its update routing table to all active
interface

eigrp :- it's classless and it refer bybrid protocol
maximum hop count is 255 means 100host
only assign the cisco router
ospf :- it's only refer class less , no limit hop
count
you assign the other router also

A user device that connects to a DCE must be which of the following? A.) DTE B.) CPE C.) Demarc D.) DCE E.) CO

1 Answers  

What is the role of the LLC sublayer?

0 Answers  

Identify the purpose of the wildcard mask? A.) Match a certain portion of the IP address while ignoring the rest of the address B.) Determine the class of the IP address C.) Determine the network portion of an IP address D.) Hide the host portion of an IP address

1 Answers  

What is the checksum?

0 Answers  

Novell NetWare has an Ethernet frame type called Ethernet_II. What is the matching Cisco command line keyword for this encapsulation method? A.) dix B.) sap C.) arpa D.) gns E.) snap F.) novell-ether

1 Answers  

what are the port numbers for DNS,FTP,TELNET,SMTP,NNTP

5 Answers   Airtel, Walton Group,

What does the Frame Relay switch use to distinguish between each PVC connection? A. data-link connection identifiers (DLCIs) B. BECNs C. FECNs D. the Local Management Interface (LMI)

2 Answers  

What is the difference between simple authentication and md5?

0 Answers  

The Internet Control Message Protocol occurs at what layer of the seven layer model? A.) Physical B.) Transport C.) Session D.) Datalink E.) Presentation F.) Network

3 Answers  

ok this is practical senario question how can we comunicate two diffrent network host by i single 1603 sires of cisco router rember that the cisco series of that router have singe 100mbps ethernet now think think write all command answer is so simple i wiil; give the answer after 20 visit til then wait

2 Answers  

Identify the command to determine if CDP is enabled? A.) show enable cdp B.) show cdp enabled C.) show cdp run D.) show cdp

1 Answers  

What port does rip use?

0 Answers