Explain how does the pulley belts are to be aligned?
- 1 Answers
- 2259 Views
- Turbo Energy, I also Faced
- E-Mail Answers
Answer Posted / saravanakumar
pulley belt are to be aligned based on two types of drives. Open and Closed belt drive.
In automobile open belt drive is most probably used(i.e cvt transmission,scooter).
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
in tpp how steam pr. decreases from steam drum to main steam line
How fuel oil consumed by medium engine?
How to calculate motor bearing life - cycle (life time) (SKF bearing)
Who has the most influence in ur life? & in which way?
What is mean by greenfield project?
Define enthalpy?
What is the meaning of probe in Boilers and that stuff?
What is the use of gravity disc?
i want technical question of mechnical for rrb mumbai
What are the 3 parts in indicator diagram?
Who built the tr alaska pipelene?
2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand
In 10.00-20 tyre. what is the meaning of .00 ( after10) ?
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
Draw the flow of F.O. diagram from service tank to Main Engine?
