I want formula to calculate cable size as per load given in
kw & amp.I searched many sites but didn't right answer.Plz
reply me asap.
Answer Posted / hosam
you have 100kva pole type TX
POWER 100x0.8= 80 kw
total load aprox: p= 47 kw
tx capactiy rate 47/100 =% 47 load
the resistance of earthing to be less than 3 ohms.
cable cu 70 squ mm to load 47 kw lengh 100 mtr
%e1= 0.0124(47x100)/70= 0.85 tolal load
from tx to panels supply 32.5 kw lengh 50mtr cable 4cxm35 mm squ + 14.5 kw lengh 25mtr cable10 squ mm
%e2= 0.0124(32x50)/35= 0.56
%e3= 0.124(14x25)/10= 0.4
%e = %(0.85+0.56+0.4)= %1,81 < %3
total of the voltage drop is acceptable
Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
why occ characteristics of generator is also called as magnatization characteristics ?
What is the rating of circuit breaker needed for 300 KVA load in 33 KV supply line in a transformer of 33 KV / 415 Volt ?
If any one's require of phoenix contact like( relay , termilnal block , surge protection device ) , product please contect me 09878206357 chetan verma
We are preparing another project which involves Waste heat recovery from a 1 MW GE Engine. The Engine in particular gives out flue gas at 487Deg C with a flow rate of 5650 kg/hour and this can be cooled to 180 Deg C. This gives a thermal output of ~ 594 KW that is available for input to VAM via heat exchanger / boiler. Additionally 581 KW will be available from engine jacket water (temperature profile 80/ 80 Deg C and a flow rate of 50m3/hr) Our estimation is that 300 TR of cooling is possible with a suitable VAM machine(s). Please advise what is the most suitable arrangement with maximum TR and min Capital expenditure. plz reply me as early as possible
Briefly define and explain the following different types of Pulse Amplitude Modulation (PAM) with some examples. i) 2-PAM ii) 4-PAM iii) 8-PAM iv) 16-PAM v) Quadrature Amplitude Modulation (QAM)
from which formula we select a capacitor rating?
1- XC and the RC time constant are both measures of the reaction of C to a change in ____? 2-The power factor is a numerical ratio with a value between 0 and 1 equal to the ______________ of the phase angle. 3-When V and I are out of phase because of reactance, the product of V times I is called ______________ power 4-For _____________ inductors, the branch currents can be added algebraically. 5- The ______________ power in watts can be calculated as I^2R 6-Calculate XL with L = 30mH and f = 1kHz ( I have Xl=2piFL 2*3.141592653*1kHz*30mH =188 ohms Please check) 7-A parallel RL circuit has the values, R = 5kohms, XL = 5kohms. A voltage source of Vt = 10Vrms is connected in parallel to R and L. Determine the total current, It delivered by the voltage source Vt. 8-A series RC circuit has R = 1Mohm and C = 1microF. How long would it take for the capacitor to fully discharge if it is initially fully charged? 9-A circuit has real power = 300W and an apparent power of 500VA. Determine the power factor and phase angle. 10-The time constant for an LR series circuit is T = 0.1s and R = 10ohms. Calculate the inductance L.
why is using sensor?what is differece between photoelectric and proxmitty?
If Neutral Grounding Resistor (GR) failed/shorted. Is it repairable.
A power transformer 4MVA/11KV/0.415Kv has been out of use in 12years. what maintenance actions/test need to be carried out before energizing.
How to calculate the value of earth capacitance in a transmission line.
how will we calculate the copper wire load..
Define settling time.
hi....I am from india..i have completed my engineering in electrical and electronics field with 58.4% and my IELTS score is 5.5 bands....Recently i received my I-20 in computer and information science from Troy university in Alabama.On 18th i have a visa interview can u please tell me what type of questions i have to answer ??????
what is the significance of cabability curve of alternator