how to calibrate pressure gauge(we can not able to fixed by pointer screw adjustment and pointer re fixing method)
- 2 Answers
- 2899 Views
- Nestle, Reliance, I also Faced
- E-Mail Answers
Answer Posted / carl_ellis
You need to disassemble the gauge to see if the movement and its linkage is broken or bent. The note below covers general gauge repair. If the zero adjust does not cover the range, a span adjustment might fix it but it is more likely that either the movement linkage is broken or the Bourdon tube has been damaged and is no longer serviceable.
Brief Overview of Pressure Gauge Repair
Pointer off its shaft
The pointer sometimes fall off under vibration conditions. The pointer can usually be replaced on the pinion shaft at least once. Severe vibration wears out all the components in the movement, eventually jamming the gauge. Liquid filling a gauge dampens vibration effects and prolongs the life of gauges.
Pointer sticks during motion
Linkage bearings can become gummed up and require cleaning, just mechanical clocks and watches require cleaning of bearings. Linkage can break (particularly under vibration) or wear to the point of jamming. Dropping a gauge can bend or jam linkage.
Pointer does not move or has very limited movement
Clogged socket or Bourdon tube
The Bourdon tube could be clogged with some substance so gummy that it prevents free movement. It is an economic decision as to whether cleaning the tube and socket is worthwhile, given the time and material costs. Be warned that a brass Bourdon tube will be damaged and weakened to the point of failure by the application of any cleaning agent with ammonia. Care should be taken not to stress bend the Bourdon tube while handling or cleaning.
If the gauge has been dropped, linkage parts might be bent out of alignment which can jam or seize the movement action.
Vibration wears and fatigues the internal linkage and movement. The bearings or gearing might have failed and jammed. Unless a replacement movement is available, we consider the gauge to be not repairable.
Adjustments
If the socket and tube are clean and the movement moves freely with no broken parts, a known pressure (roughly mid-scale) is applied to the gauge with a dead weight tester or is applied from a pressure source and monitored with a certified 'test' gauge; both are (relatively) expensive devices. Adjustments are made to for span and zero.
Zero Adjustment
A known cause of a negative offset in liquid filled gauges is when the case vent is stuck closed. Vent the gauge with the vent located somewhere near the top of the case so that positive or negative pressure does not build up inside the case and cause an offset.
The zero adjustment method depends on the gauge design/construction (also a relative indicator of quality). The methods include
- adjustable pointer
- cam adjustment in movement
- dial rotation
- pointer removal and replacement at a different position on the pinion shaft
- none
An adjustable pointer provides about 10% (full scale) adjustment.
Gain, Fast/Slow adjustments
Gain or Fast/Slow adjustments can be made by various adjustments - slotted links, adjustable length links, U or O (horsetrack) links that are squeezed close (to shorten) or open (to lengthen), to name a few.
Calibration NEVER involves bending or repairing the Bourdon (C shaped) tube or socket. A Bourdon tube that has been over-ranged is stressed to a point that it will not indicate the pressure accurately and it can not be fixed. A Bourdon tube that leaks can not reliably be repaired and needs to be discarded.
2 informative Youtube videos:
Adjustable pointer on Ashcroft process gauge
https://www.youtube.com/watch?v=VbAke-0ijws
How to Reset a Liquid Filled Pressure Gauge
https://www.youtube.com/watch?v=SvpsWjan6Wc
Obtaining parts for all but the highest quality gauges can be problematic.
Most gauge manufacturers no longer offer repair parts for gauges, although some do for the highest level quality gauges.
Carl Ellis
Measure First
| Is This Answer Correct ? | 2 Yes | 0 No |
Post New Answer View All Answers
Can I calibrate the Electromagnetic Flow Meter on line and How.
Whatis the reset ofset and control system in instrumentation
What is the formula of vabration sesore. i mean how to covert mils to volt plz share if any body knows very argent : my mai is merajalam143545@yahoo.com
For what reason would you possibly be compelled to make use of a Smith Predictor. Explain the idea behind the operation of this device.
2. What is ultrasonic flowmeter?
Q1]IF THE RANGE FOR FLOW IS -35 TO 125 WHAT WILL BE THE SPAN FOR ABSOLUTE AND FOR NORMAL? Q2]HOW TO CALIBRATE CAPILLARY TYPE LT? Q3]HOW MANY ERROR CALCULATIONS ARE THERE USED IN PROCESS INDUSTRIES? Q4]HOW TO CALIBRATE TEMPERATURE TRANSMITTER? Q5] HOW TO CALIBRATE LEVEL TROLL AND HOW TO CONNECT? Q6]PLEASE TELL ME THE BASIC FOR INSTRUMENTATION WHICH IS APPLIED FOR CALIBRATION AND FOR ALL? PLEASE MAIL THE ANSWER TO honest_yes@yahoo.in
how to measure draft pressure in transmitter pl. give its single line digram
Somebody can explain me about >Critical Loops, calibrations, ESD critical Loop checks, Logic Diagram / Cause & Effect checks for ESD loops,
How to calibration coriolis flow meter?
What is Predictive Maintenance
What is the purpose of LO Overhead tank in turbines.
DEAR SIR/MADAM MY NAME IS ARKAPROVA BHATTACHARYYA.I AM A FRESHER INSTRUMENTATION ENGINEER.CAN YOU PLEASE SEND SOME QUESTION PAPERS OF GRADUATE ENGINEER TRAINEE EXAM OF DVC(DAMODAR VALLY CORPORATION).MY EMAIL IDs ARE arka_aec@rediffmail.com.
List three types Level Gauges with their working principles
What is stripper & spilitter ? Diffrence in this.?
any one can send me instrumentation previous interview papers? I prepare for MNC Company Interviews? my mail id- Rakesh.Golla@dodsaldxb.ae , and another mail rakesh.gvk@gmail.com
