How to calculate stirrups cutting length in columns
- 2 Answers
- 19989 Views
- Construction, I also Faced
- E-Mail Answers
Answer Posted / karunya31
1) let cover for column be 40mm (as u have not mentioned)
formula to determine cutting length of stirrup is given below
cutting length= (2A+2B)+(24D)
A=LONGER LENGTH OF COLUMN-2XCOVER=400-40X2=320MM
B=SHORTER LENGTH OF COLUMN-2XCOVER=250-40X2=170MM
D= DIAMETER OF STIRRUP BAR IN MM
therefore
cutting length=2X320+2X170 + 24X8 =1172MM=1.172 meter
2) given cover 25mm (as u have mentioned)
formula to determine cutting length of stirrup is given below
cutting length= (2A+2B)+(24D)
A=LONGER LENGTH OF BEAM-2XCOVER=400-25X2=350MM
B=SHORTER LENGTH OF BEAM-2XCOVER=200-25X2=150MM
D= DIAMETER OF STIRRUP BAR IN MM
therefore
cutting length=2X350+2X150 + 24X8 =1192MM=1.192 meter
NOTE SLAB COVER HAS NOTHING TO DO WITH CAL.OF STIRRUPS
3) ASSUME cover 30mm (as u have NOT mentioned)
formula to determine cutting length of stirrup is given below
cutting length= (2A+2B)+(24D)
A=LONGER LENGTH OF COLUMN/2 -COVER=400/2-30=170MM
B=SHORTER LENGTH OF COLUMN-2XCOVER=250-30X2=190MM
D= DIAMETER OF STIRRUP BAR IN MM
therefore
cutting length=2X170+2X190 + 24X8 =912MM=0.912 meter EACH
Generally term stirrups are used for lateral tie for beams while term ring is used for columns.calculation of length for stirrups & ring are same. Stirrups length depend upon size of column/beam,cover,dia of stirrup's bar.Nominal cover is measured from outer face of stirrups to concrete face.Although this cover at site is measured from outer face of main bar.If cover for beam is 25 mm then, for 90 degree hook for 600x400 mm column & 10 mm dia bar as per IS Code 2502 length will be=2[(600-2x25)+(400-2x25)]+20x10mm=2000...
If there are four bar of 20mm dia on 600 mm face then for central stirrup of this side will be=[600-25-25-(20/2)-(20/2)]/3=176.66 between centre of two bars of this face,now add (20/2)+(20/2) so that outer face to outer face of 20 dia bar=196.6say 197mm. same way other side of central stirrups are calculated & then add 20 times bar dia.Add 24 xdia of bar for 135 degree hook
In IS code formula=2(A+B)+20 x bar dia. A & B are internal distance between stirrup side.
| Is This Answer Correct ? | 9 Yes | 2 No |
Post New Answer View All Answers
What is the material consumption- cement,sand,tiles etc for Toilet dado?
01. a. Diagram of a slump cone…………… 1 b. Size of Slump Cone…………… 1 c. Volume of a slump cone by av. Dia method…………… 1 d. Volume of a slump cone by av. area method…………… 1 e. Volume of a slump cone by frustrum method …………… 1 f. Angles of slump cone …………… 1 g. Slump measured by slump cone due to…………… 1 h. Slump does not measured by cylinder / cube due to …………… 1 i) ii) i. Slump cone is to be filled in……………………..Layers.
What is the mix propotion of M10,M15,M20,M25,M30,M40,M50.M60 cement content,aggrigate,sand and water ratio.
what is zone a n zone b?why the spacing of ring in zone a less.n zone b high?
load combinations how many types for staad design purpose?
Which prize is the alternative to the NOVEL Prize?
how many minimum admixtures are used in water froofing structures
How many hours should traffic be not allowed after completing wbm road or bst.and min how many hours should road rollers be used.
What is a bearing capacity of soil?
1.How much batten required for 1 sqm Shuttering. 2.how much pipe & clamps required for staging of 100 sqm shuttering at 5.0 m height.
What are the common ways of demolition?
How musch steel i.e. angles, channels,and square pipes are required per square feet for a steel roof of residential two storied building?
Write short note on construction programme for pile foundation.
How to get MEP technical,instaaltion & testing data for interview?
What does civil engineering mean?
