LADDER LOGIC
Can any body state Logic on following condition
Instructions to use 1-XIC 2-XIO 3-Output ONLY
Program
Push 1st button On - 1st lamp should On
Then Push 1st button Off - 1st Lamp Should remain on
Push 2nd button On - 1st lamp should Off and 2nd lamp should On
Then Push 2nd button Off - 2nd Lamp Should remain on.
- 4 Answers
- 6957 Views
- I also Faced
- E-Mail Answers
Answer Posted / mohammad wasim khan
rung1
xio (adress I:0/1) pb series 2 xic puch button in paralllel and give adress as(O:0/0) to one of xic pb and adress (I:0/0)to second xic , a output in series with adress O:0/0.
rung 2
xio (adress I:0/2) pb series 2 xic puch button in paralllel and give adress as(O:0/1) to one of xic pb and adress (I:0/1)to second xic and a output in series with adress O:0/1.
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
Explain the working of an electronic level troll.
What is 3 element control system
i want to know the interview format fot gail, instrumentation. pls answer me in habib.sami1003@gmail.com
What are the interlocks we have to check during the start up of LP/HP compressor?
what is a half wave, full wave, and bridge rectifer.
what is commisioning procedure,2)what is is the main work in commisioning in the field tx to dcs, plz send me detail
what is compensation? temprature & pressure
how radio frequency level probes works with its controller ? what is its principle ? pls give me brief explanation?
Explain why plc require in analog input 4-20amp & 0-10 volt?
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
can anyone tell me about the basic concepts to consider before to start a PLC panel wiring
Q- Control problem are mainly classified in _____ types. a-)4 b-)3 c-)6 d-)nono of these Few of them i know is 1- regulator type problem (eg- Air conditioner) 2- tracking problem (eg missile trcking problem) 3- sybernatics 4- optimal control problem
How we calculate orifice plat size???
Exothermic reaction./ endothermic reaction
plz send me general of ongc
