These questions were asked at NICL for the post of
Administrative Officer(Specialist):
1. Questions on B.Tech Project
2. What is camshaft and its working
3. Shape of a Cam
4. If Otto and Diesel Cycle has same compression ratio that
which will have higher efficiency
5. Effect on IC Engine efficiency if inlet temp increased
6. Who is the current world champion in Chess(as of Sept 2012)
7. Sports person involved in dope charges(Lance Armstrong)
8. Formula for Otto cycle efficiency in terms of temperature
9. 2016 olympics will be going to held in which city
- 2 Answers
- 7685 Views
- Atlas Honda, JL, NIC, I also Faced
- E-Mail Answers
Answer Posted / ravi kumar singh
A Shaft with a cam for each intake
and exhaust valve. working of
camshaft to operate the inlet or
exhaust valve.
| Is This Answer Correct ? | 3 Yes | 0 No |
Post New Answer View All Answers
what is pulverisation
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
What causes diesel engine to automatically stop?
can a deareator be placed at any height with care that suction (NPSH) for feed pump is satisfied
What Is C.G. And M.I. in simple
Why should a chain drive be used over a belt or rope driven drive? State pro`s and con`s?
what is run out? how to calulate run out vaue.
What is the cause of cylindrical liner overheating?
What is higher IMP or BHR
What happens when too much cylinder oil is injected in the working cylinder?
What is the use of pneumatic system?
Where can you find space heater lam p and what is its purpose?
What are the procedures of starting of diesel engine?
pls tell me the process to set up a power plant right from the permission from state govt ????
What is the difference between Over Molding and insert molding ?
