WHY WE ARE DOING THE EARTHING IN A SYSTEM. SOME PEOPLE ARE
TELLING FOR PROTECTION. WHAT PROTECTION GIVE ME THE CORRECT
ANSWER.
- 2 Answers
- 3638 Views
- I also Faced
- E-Mail Answers
Answer Posted / s.sakthivel
Basically three type of fault develop in the circuits
1, open circuits
2, short circuits
3,loose conection
4,body short
first three electrical fault are directly not distrub humen
and apparatus and last one (body shor) fault is directly
distrub humen and apparatus
so , body short fault time current is to discharge to
ground by the root of earth electrod, so we are addapted
every apparatus earthing system(vanthni@yahoo.com)
| Is This Answer Correct ? | 1 Yes | 2 No |
Post New Answer View All Answers
Explain the following and how these are working with PLC Unit 1 I/O Module Card 2 Adaptor Card 3 Ribbon Adaptor 4 I/O bus 5 I/O Devices
formula for calculation of switchgears(i.e. contactor, fuse, cb, relay etc.), if load current is given?
hi this is hema, r there any books in particular for the preparation of the APPSC-A.E.E(electrical), if so please mail me the names ... thank u .
7- What is the Dissipation Factor and the difference between it and Insulation Resistance Test? 8- What is the task (function) of DC and AC reactors in power plant? 9- What is the task (function) of (open delta with earthed) in some types in transformers? 10- What is the base of the selection of the vector group in transformers? 11- What is the zig-zag transformer and its function by drawing in large detail? 12- What is the polarity ? 13- Why we make short between phase(R) in high side and phase (r) in low side in vector group test? Where High Side ( R ,S and T ) and Low Side ( r ,s and t ). 14- What are the time on delay and time off delay? 15- What is the vector group? 15- What is the task (function) of different types of vector group such as Dyn11 , Dd0 , YNd1,……..,?
should %impedance be high or low in a power transformer? if so why?
What mean by MLTP
How does a transformer contribute towards the widespread popularity of ac system over dc?
What is the difference between in Fourier series and Fourier Transform. and please tell me the difference between both of them and the why we use them in communication system?
how to get electrical supervisor competency certificate in gujarat. i did 3 year diploma in electrical
My question is whether bellow formula is correct to find bus size for 46kA for 0.5 second & what is RT in bellow formula. formula to calculate the size of busbar to withstand the thermal stresses due to currents with duration of 0.2 sec to 5 sec. Sp = RT( I x I x t) / K Where Sp – is the cross sectional area of bus bar in millimeters. I - is the value of AC fault current. t - is the operating time of disconnecting device in seconds. K – is the factor depending on the material of the conductor, insulation and initial and final temperature. Value of ‘k’ for copper is 143.
Define coil span?
At the starting of dc motor and syn.motor and induction motor high current flowing through the winding. Due to this the windings burnt out. To avoid this different types of starters are used. But incase of transformer what Will be used (At starting no emf is induced in the primary winding)?
What is oscillator circuit?
how to calculate units consumption for a 12 hp motor /hr.
we have require a Motor (1500kW, 6.6kV, 50Hz) which shall operate at 1500rpm during 30min and after it shall run on 500rpm during 15min. The same cycle shall be repetitive during the whole working days. Which method is best and economic to achieve such type of task. VFD, VVFD, Pole changing motor etc.
