why generation of syncronized generator increases when
frequency of grid is less then 50Hz & generation decreases
when grid frequency goes up from 50 Hz, as comparision with
set value entered in govering panel?
- 1 Answers
- 3005 Views
- I also Faced
- E-Mail Answers
Answer Posted / vasanth
The Line Frequency is influenced by the Grid as that is
Infinite source. Since it is in Synchronized Pattern the
generator is influenced by the GRID. Due to the effect of
speed control Governor in the generator which fails to hold
the speed on its own due to other source which is
influencing, raises the fuel flow ,Flex raises and generator
take the additional load from the Grid. This is How the Load
is distributed across the sources .
| Is This Answer Correct ? | 0 Yes | 1 No |
Post New Answer View All Answers
What pressure results for a flow transmitter of range 0- 180t/h in the dcs and 0-301mbar in the field using square root extraction. Kindly also suggest formulae for the percentages 0,25,50,75,100?
What is the purpose of bypass valve across AS valve.
If i have 4 Allen Bradely make RS logix 5000 PLC and for viewing that we are using 4 RS view SCADA for 4 different packages. Now, I will want to view two packages on only one SCADA. Then how i will do it?
How process line mpm calculation is done?
how to tune siemens sipart electro pneumatic positioner..plz tel me..
I have energy meter for educational project having 0.5s class but my friend need 0.2s class meter , which one is good for that purpose and what is the actual difference of that two classes , need very easy example also.??
full process of gas turbin?
Type of level transmitter commnly used in Procees area are the following. a.________________This type of level transmitter works as follows
how many type of plug are used in pneumatic control valve,name them.
Hello to all....I am an Instrumentation Graduate and i am passed out in this year only.. I am unable to find the job in my core instrumentation.. so any boby tell me how to and where to search the job....please...and also tell me i there are any courses offered in the instrumentation stream so i can do it... you can send your suggestions to my mail-id i.e Ganesh20084u@gmail.com ... please..
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
What is the principle of capacitance type level transmitter?
i want formula for flow control.am doing project in flow control using orifice . i know value of the flow level(Q) . upstream(p1) pressure, orifice diameter(Do) , pipe diameter(Di) and oil viscosity(Vi) how can i calculate downstream pressure
can u briefly explain aboutan aryton shunt multirange DC ammeter?
If fire would be inside the plant which fire detector is to detected the fire.
