Interested to Buy Any Domain ? << Click Here >> for more details...
what is phase to phase voltage? what is line to line voltage
- 46 Answers
- 143803 Views
- Exmar, HBL Power Systems, I also Faced
- E-Mail Answers
Answer Posted / anil
actually question is not clear
question should be "what is phase voltage @line voltage."
Phase voltage is phase to neutral voltage.
line voltage is phase to phase voltage.
| Is This Answer Correct ? | 9 Yes | 0 No |
Post New Answer View All Answers
Hello Guys !! i want to rrb section engineer electrical(signal) previous model papers? any body help me?
what is the function of gss in the dg set.
difference between ac series and parallel circuit
What happened when voltage will half value of current ...
What should be the length of transmission line so that we can see/obtain the full sine wave of voltage??
how commomn gate triggering is given for TRIAC ? other thyristor wont be efffected?
1. What is differential relay? How it operates? 2.How to calculate the Short Circuit Impedance in Transformer? 3.What is the alternate solution for testing of polarity by using polarity tester while its milli ammeter does not works? 4. While testing the 33KV Busbar by using Hipot kit, what should be the test voltage we have to apply? 5. What is the procedure/activities to be taken to inject the current more than 2000A by using 2000A Loading Transformer? 6. Explain how you can give the overload setting to any Motor Protection Relay for a HT motors with formula and example? 7. Why restricted earth fault protection is needed? Why can’t differential Protection is sufficient? 8. What should be the minimum and maximum ohmic value for earthing? 9. Why DC Currents are not used in transformer? 10. What is the Frequency while we step up the voltage from 220V to 11KV? Is it possible? Explain it?
On a 6 KVA UPS we have to provide a DC MCB for Battery bank of 16 nos (12 V 42 AH). What Shall be the current rating of DC MCB ?
DEFINE BREAKING CAPACITY OF BUSBAR & HOW IT IS CALCULATED?
Does all the output contacts (N/O as well as N/C) of a Numerical relay operate when relay receives a binary input/inputs or contacts are designated to specific logic input/inputs and only these contacts operate?
how to find 5 kilo meter long under ground 33 kv cable fault location if IR VALUE shows 0.05 M ohm @5000 volt.and cable fault locator shows some time fault distance 3 kilo meter ,3.7 kilo meter and some time 1 kilo meter? now how to find the fault location that where is leakage. note--it is tested with 5000 kv megger and insulation resistance is 0.05 M ohm. and some time 0.03 M ohm comes.
How short circuit MVA(Fault MVA) in a power system calculated for calculating number of earth plates ?
Will an earth leakage trip be activated if the component or wiring is faulty on low voltage equipment.Example An electrical Cat Scarer placed in the garden and water gets into the wiring.
i need to now what will be the cable size to the following load, transformer to distribution panel distance 110m, load 1000kw, voltage 400v, pf 0.85, permissible voltage drop 2.0%, overhead line, atmospheric temperature 35 degree c.
My question is whether bellow formula is correct to find bus size for 46kA for 0.5 second & what is RT in bellow formula. formula to calculate the size of busbar to withstand the thermal stresses due to currents with duration of 0.2 sec to 5 sec. Sp = RT( I x I x t) / K Where Sp – is the cross sectional area of bus bar in millimeters. I - is the value of AC fault current. t - is the operating time of disconnecting device in seconds. K – is the factor depending on the material of the conductor, insulation and initial and final temperature. Value of ‘k’ for copper is 143.
