Interested to Buy Any Domain ? << Click Here >> for more details...
hello this is dhinakar i am completed my instrumentation
engg . recently i got job in sugar industry side. i like to
ask one question can any one say what are the things i have
to follow know more about industrial instrumentation,,,,,,,
- 6 Answers
- 9307 Views
- I also Faced
- E-Mail Answers
Answer Posted / mazhar ali
hi,congrats
always carry a notebook and pen with you
observe each and every instrument in the plant
make a note of all instruments you see day by day
try to find out its function input output range and use make
a note of that.
study the entire plant working process.
apart from above learn this
calibration of pressure,temperature gauges.
calibration of all types of transmitters like
pressure,level,temp and flow transmitters.
Calibration of thermocouples and rtd.
installation of all transmitters,thermocouples ,gauges.
PID,ON-OFF controllers use and programming.
loop checking and pre commissioning procedure.
functions of HART communicator,Fluke and dead weight testor.
PLC ,SCADA AND DCS
all of the above may not be available in your plant but its
the must thing for an instrumentation engineer to know.
| Is This Answer Correct ? | 6 Yes | 0 No |
Post New Answer View All Answers
Draw a great bridge circuit.
Tell about your IFFCO plant visit.
Differentiate between ultrasonic flowmeter and radar type flow meter
Make Heater Process Logic.
What is offset in a control system.
what is the process to make control schematic ?
please someone tell me what is function of vibration sencer and how many types and how to control viberation.please. my id is jimmykhan077@gmail.com
what are the documents(Construction point of view for a process plant) submitted by contactor initially entering in to new site for client?
Describe the typical instrumentation used in monitoring the performance of a shell and tube heat exchanger.
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
can any one explain in which term we are flow flow is it volumetric r is it mass? and y
What are different types of orifice plates? State their uses.
why we are using drum level control valve air to close?
If i have 4 Allen Bradely make RS logix 5000 PLC and for viewing that we are using 4 RS view SCADA for 4 different packages. Now, I will want to view two packages on only one SCADA. Then how i will do it?
IN CONTROL VALVE SPECIFICATIONS GENERALLY TERM " DE- 200" ."DM -400"USED,, WHAT IS DE/ DM STANDS FOR?
