1. alternator has full load regulation of 4% when pf of the
load is 0.8 lag, 1500 rpm. full load regulation of 1400 rpm
for 0.8lag will be ________ ??
2. torque angle of a sync m/c operating from a constt
voltage bus is usually defined as space angle between _______ .
3. method most effective in finding out no load losses in
large DC shunt motoris ______ .
4. current carrying capacity of fuse material depends on
______ .
5. coil has res. 10 ohm, inductance 1H. what wil be current
after 0.1sec after switching on to a 500V DC SUPPL ? ?
6. effect of phase lag compensation on servo systems
___________ .
7. rotor of a dc machine is usually supported upon ______ .
8. DC motor is preferred to AC motor in which application ??
9. 3 nos of 10:1 Xmer are connected in Star-Delta to supply
a load at 230V.the supply voltage must be ______ .
10. voltage source produces max current in which circuit.
11. cal. power, if current and voltage are out of phase by
90 degree.
12. suitable length of Xmission line of power at 66 KV.
13. Which of the theorm helps in simple computation when the
load across a ckt is varying ??
14. what is the adopted line length for power Xmission of
power by cables ??
- 5 Answers
- 7038 Views
- TATA, I also Faced
- E-Mail Answers
Answer Posted / rajnikanth
for tenth one it's short circuit
| Is This Answer Correct ? | 3 Yes | 0 No |
Post New Answer View All Answers
What is Meter MF if External CT Ratio is 150/1 , PT Ratio is 132/110 Meter CT Ratio is 200/1 & Meter PT Ratio is 110/1
If I want to lift the water at a height 50m from ground level through two inch(diameter) metal pipe then what is the capacity of motor pump is required? is it possible in single phase supply or not?
Why single phase induction motors are not self starting ?
WHat is the general checks required for Dry type transformers
why asa method ZPF method is more accurate than ASA method?
we have one oven for 12 zone we are installed ir lamp in oven we control load from thyrister and 0 to 5vdc so our zone no 8 getting bright in fraction of second so what we do.. Please answer
mccb service sittings be done?
(1)WHAT HAPPENS WHEN SUDDENLY LOAD GIVEN TO THE INDUCTION MOTOR ? (2)CAN WE MAKE WOOD AS MAGNET ? (3)WHAT IS THE VALUE OF MAGNETIC FLUX DENSITY IN TRANSFORMER ? (4)WHY WE ARE USING ELECTROMAGNETI NOT ELECTROSTATIC IN MACHINE ?
What is the polarization index value ? (Pi value)and simple definition of polarization index ?
hai now i am working as a electrical design engineer in construction field can i get a job in oil and gass field or power plant project as a electrical design engineer?
How does "OUT OF STEP" relay ,for Synchronous motor protection, work?
what is meant by 2 within a star in a voltmeter dial?
relation between power station capacity and voltage level?
I want to put this query to SENIOR & EXPERIENCED ELECTRICAL ENGINEERS. 1)I want to know about the control circuit diagrams for control panels. I found it difficult to understand. Is there ant booklet through which we can learn the circuit diagrams? 2)I want to learn about conduiting, laying cables, preparing cable schedules and various techniques which is the part of building infrastucture(construction field). I don't have any experience in this area. I have experience in control panels only. that's why i am not getting any opening in building infrastucture (construction field).Can I get the job in this field as Trainee Engineer? How to enter this field? I need job in PUNE
How to design pavement quality concrete by using C.R.C.P Method
