Interested to Buy Any Domain ? << Click Here >> for more details...
What is the working principal of Mass flow transmitter?
- 1 Answers
- 9274 Views
- I also Faced
- E-Mail Answers
Answer Posted / sam
It is a combination of a flow meter and a density meter
combined either as one unit or two separate instruments and
the final mass flow calculation gets done at a remote
location. Good example of a all in one unit is the Coriolis
meter. You can read the flow, the density or the mass flow
directly from it and configure its output to give you
whatever you need to be displayed on your supervisory system.
The principle it works on is vibration tubes. The variance
in vibration is a direct and proportional result due to the
variance in flow. So the frequency of the vibration is
monitored and converted into the output signal obviously
with some calculations inside to get the density and mass
flow as well.
Good luck
| Is This Answer Correct ? | 23 Yes | 3 No |
Post New Answer View All Answers
How can a d.p. Transmitter be calibrated?
How the warning lamp of a charging-system is activated ?
How to fix back the valve actuator stem
selection criteria of control valve? and selection criteria of actuator explain in brief?
Punj lloyd is coming in our Jadavpur Universtiy campus for campus placement. Please send me some hints about the writtend exam. My email id is subratafriends@gmail.com
Hi,can anyone help me out with PhD programs related to Instrumentation field?I have a degree in electronic Instrumentation?
3. Differentiate between ultrasonic flowmeter and radar type flow meter.
use of split range ? where it is used ? in which control loop it is used ?
dear sir we have insatlled positioner model no.sipart PS2 make Siemens at our control valves . now problem is if we want to increase the response of valve opening speedy /fast. what parameters do we change for positioner ? any idea. please guide us.
hello sir/madam, I,Subramanian need 5yrs placement papers of officer trainee of Instrumentation technology.pls send to this mail id mani_nxtgen@yahoo.co.in please do the needful. with regards, subramanian.v
how does we calibrate a square root flow transmitter ,give an example and explain it step by step like range calculation , calibration hook up series connection , zero check , and how to apply pressure , and if not geting proportional output then what should we do ?
Explain the working of an electronic level troll.
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
what will the sending unit in the fuel gauge utilizes?
when placing a vent or drain hole on an orifice plate should you measure from the center of the bore up or down for the vent placement?
