what is full form of SMART
- 46 Answers
- 79610 Views
- Infosys, ITC Infotech, Lanco, Rosemount, Solvay, I also Faced
- E-Mail Answers
Answer Posted / renu thushar
From a Quality perspective, SMART stands for Specific, Measurable, Achievable, Realistic, Time-bound
| Is This Answer Correct ? | 14 Yes | 4 No |
Post New Answer View All Answers
what is the responsibility of an instrument commissioning supervisor
few questions on RS 232,1 question on relationship of impedance and turns ratio, many questions on flowmeters
(1) In turbine, what does term CDP, NI, NH, HSSOC, means. (2) What is the purpose of LO overhead tank in turbines.(3) An equipment is certified for EEX, IA, IIC,T6, what do you under stand by this.(4) what is SURGE, and how it is prevented, what is the purpose of bypass valve across AS valve.(5) Give 2 application of quartz crystal used for process parameter measurement.(6) what is meant by cold float of compressor shaft. (7) state four different types of flow measurement. For gas flow measurement mmscfd is the common unit. Expand the unit and specify significance of word S in the unit.(8) what is meant by Gap voltage, in vibration measurement. Normally how much Gap voltage is set and state the reason.(9) what will the new flow factor if D/P transmitter is Re-Ranged from 25” wc to 50” wc.(10) what is the usage of QDV & Volume booster.
line up procedure for dp type flow transmitter?
how to design orifice plate?what is the equation?
Why ac supply load cell is used? Can we use the dc supply load cell?
Which are all the commonly used Bordon tubes in the pressure gauges. Do any one use ASTM A 312 tubes for this purpose?
What are the type of bonnets in the control valves?
If we increase only P what will be controller action ?
hello can yoy pls send me previous papers of jindalpower and steel ltd.....'m from instrumentation..... mani1048@gmail.com
Hi my friends Is any one who can assist me in knowing the typical interview questions for system engineer at General Electric pty Ltd
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
what do u mean by compensation n pid tunning?in pid tunning what you tunned?is it possible 2 tune p i d
how many type of plug are used in pneumatic control valve,name them.
what is the input of digital counter during the the calibration time?
