When batteries are connected in series the voltage increases
but the current remains unchanged, how can this be?
When you consider ohm's law. i.e.
If voltage increases, current increases, providing
resistance remains the same.
- 10 Answers
- 10276 Views
- I also Faced
- E-Mail Answers
Answer Posted / amarnath
I dont know how voltage increases??? if the batteries are
connected in series......
| Is This Answer Correct ? | 3 Yes | 3 No |
Post New Answer View All Answers
What is UPS and How do you maintain the UPS Maintenance? Brief Description on UPS maintenance.
Why is voltage is required to be within permissible range for an electrical equipment?
Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1. H1-H2 = H2-H3 H3-H1 2. H2-H3 = H3-H1 H1-H2 3. H3-H1 = H1-H2 H2-H3 For the LV side also: 4. X1-X0 = X2-X0 X3-X0 5. X2-X0 = X3-X0 X1-X0 6. X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0 H2-H0 H3-H0 X0-X1 X0-X2 X0-X3 128.0 119.9 7.2 29.2 13.3 15.8 70.7 128.4 59.2 23.4 22.0 3.6 7.2 120.1 128.1 13.4 29.3 15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?
we have an energy meter in a capacitor bank panel, So should we consider it's readings as energy consumption on daily basis. (when capacitor bank doesn't have any energy losses)
list the type of vfd? wich is sutable for heating kiln?
USE OF 8 WAY PAN ASSEMBLY
what is the IS foe lightning arrester?
Earth is a conductor or load?then ammeter connect to 3- phase supply,it shows the measurents or not?
What are the disadvantages of hydropower?
What is the formula for selecting the cabels according to load? How to calculate what sq.mm cabel to be used?
block diagram of 2 ups system connected in hot stand by mode?
which type of amplifiers are used in multimete?
How i can calculate current of cable according to ares?
What is the difference between isolators and electrical circuit breakers?
We have drive feeding an output contactor for a 5000 hp motor @ 5kV application. The motor FLA is 629amps x 1.25% service factor = 786.25 amps The cable that we current have in place between the drive and the output contactor is 350kcmil- MV-105 (parallel cables). Per the NEC table 310.60 (C) (69). This show the cable ampacity is at 615 amps per cable for a rating of 1230 amps. We have derated the cable for the cable tray and the multiple cables application and our calculations show that after the correction factor factor we are at 922amps. 1230 amps x .75% correction factor factor = 922.5 amps. The customer is driving us to then use another safety factor of .25% off of the already derated cable. Can you please provide a longhand calculation for your solution on this application?
