Interested to Buy Any Domain ? << Click Here >> for more details...
Hi, All
I am configuring EIGRP in Packet tracer, after configuring
all the things it is not working but in one condition it is
working fine if i am putting all my router and network
withing one network subnets e.g. 172.16.0.0 or 10.0.0.0 but
whenever i am puting different network subnets e.g. in one
network it is RA(config-if)#=ip address 10.0.0.1, and in
fa0/0= 192.168.1.10 and in RB(config-if)#10.0.0.2 (s1/0) and
in S1/1 11.0.0.1 and in fa 0/0 192.168.100.1 ,where as in
third router RC(config-if)#=ip address 11.0.0.2 and in fa
0/0 172.16.1.10 and after configuring all this serial is
showing up and protocol showing up but eigrp process not
taking place after adding eigrp configuration, i tried with
"no auto-summary" command but not working.. Suggest me where
i missing something? can mail me at : gtech.innovator@gmail.com
- 20 Answers
- 27774 Views
- I also Faced
- E-Mail Answers
Answer Posted / gt
dear jitendra,
keepalive i think only work on serial interfaces not on
ethernet (router) so i set given output after setting "no
keepalive" on serial.
If you say i can send you at your mail, the detail diagram
with configuration and then you can try at your end.
Show RUn
Current configuration : 655 bytes
!
version 12.4
no service password-encryption
!
hostname kolkata
!
!
!
!
!
ip ssh version 1
!
!
interface FastEthernet0/0
ip address 192.168.1.10 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Serial1/0
ip address 10.0.1.1 255.0.0.0
no keepalive
!
interface Serial1/1
no ip address
shutdown
!
interface Serial1/2
no ip address
shutdown
!
interface Serial1/3
no ip address
shutdown
!
interface Vlan1
no ip address
shutdown
!
router eigrp 100
network 192.168.1.0
network 10.0.0.0
no auto-summary
!
ip classless
!
!
!
!
!
line con 0
line vty 0 4
login
!
!
end
SHow ip interface brief
kolkata#sh ip interface brief
Interface IP-Address OK? Method Status
Protocol
FastEthernet0/0 192.168.1.10 YES manual up
up
FastEthernet0/1 unassigned YES manual
administratively down down
Serial1/0 10.0.1.1 YES manual up
up
Serial1/1 unassigned YES manual
administratively down down
Serial1/2 unassigned YES manual
administratively down down
Serial1/3 unassigned YES manual
administratively down down
Vlan1 unassigned YES manual
administratively down down
| Is This Answer Correct ? | 3 Yes | 1 No |
Post New Answer View All Answers
What s the formula for metric of ospf?
What is the checksum?
What does routing mean?
Which cable called roll-over?
What is the difference between csma/cd and csma/ca?
What is the difference among straight cable, cross cable and rollover cable?
What are the advantages of lan switching?
What is point-to-point protocol in ccna?
What is etherchannel?
What is the difference between the user mode and the privileged mode?
How do areas benefit a link state inter network?
What port does rip use?
Hi Friend. i have to let you know that now i have been selected for cisco india in bangalore. i am thanking to all of you guys that u have been posted such good question and the respective answer. from today i will be not able to visit this site on regular basic and hopeing that you will continue to post the question.the question you are posting is not very usefull to you but also usefull to another. i am again thanking to all of you and hope for best for your feature. Jitendera kumar sinha Network engineer-L2 cisco india Bangalore
Which protocol called rapid protocol?
Which command we give for live view of remote site routers?
