Based on CPI/CGPA they shortlist the candidates & than
directly start Interview so there is no Written Exam or GD
Only PI.Interview held @ MNNIT , ALLAHABAD On-Campus on
6th,Aug, 2007 & the Questions asked to me by Interview Board
( 4 People) are from HR/SummerTraining/BTP/Subject-core,
POWER SYSTEM & MACHINE. time duration of I/V is about 15-20
Minutes.
HR-
Q.1 Name,hobbies & About family background ?
Q2.What u know abt NTPC ??
Q3.Why u want to choose NTPC as ur Carrier's starting i.e
power sector not any other Oragnisation or sector ??
Techincal Questions-
Q1.What is the reason for transformer Noise ??
Q2.Which material is used for making Transformer oil & How u
measure its dielectric strength & Name the test ?
Q.3 Which Machine u will prefer 2 use if flammble gases are
coming out at a place & why ??
Q4.What is relation b/w Transmission Lines & Communication
Lines ?
Q5.What is the maximum capacity Synchronus Machine & total
powerGeneration in our country ?
Q.6 In india Power generation is at 50Hz while in America
its 60 hz ,why so ?? Advantage or disadvantage ??
Q.7 Maximum Generation Voltage in india ?
Q8. What is the Voltage regulation & why its required n how
much is permissible ? & causes of voltage variation ??
Q.9 Why electric shock is feel ?? n in a Electric Train why
we didnt feel that ?
Q.10 Have u seen/ experience of any power plant/ industry
related to the power sector ?
so these are the questions which not too diffcult i
think was asked to me.
- 6 Answers
- 10123 Views
- NTPC, I also Faced
- E-Mail Answers
Answer Posted / divya
Can you please give me the answer for Q) 3, 5, 7, 9
| Is This Answer Correct ? | 0 Yes | 1 No |
Post New Answer View All Answers
Some times to change of DOR of a motor, interchange of R & B is not effected and RYB take same current, but interchange of R&Y is effected ie change the DOR. My doubt is what is the problem in motor and how it is happen.
When distance between two pulleys is not fixed, the tension of belt is adjusted by a) driver shaft b) driven shaft c) adjustment screw d) belt
Haw to check conductivity of budbar
for opening electrical shop, tips needed.
What is ignition module of a CAT Gas Genset G-3508 Engine, Alternator SR4B Series. HOw its checked for correct functioning.Is it repiarable or replacable?
WHAT IS THE MEANING OF BALANCED / UNBALANCED IN STABILIZER TYPES.
what is the difference between "Rotary bypass isolation switch and Normal bypass switch" pls share indepth techs?
How we select the vector group of 3phase power transformer?
Earth has zero potential then what would be the neutral potential ?
At what speed 1 HP motor can run an electric car of weighing 400 kg?
how we can calcultae the short circuit level for bus bar
What is effect of over voltage and under voltage on ACB
What is the previous name of Cox's Bazar
Sir,In our company there are 3 caterpillar make(capacity:(1) 3.3KV,2.5MW(2)3.3KV,2.5MW & (3)3.3KV,1.9MW) & 1 deutz make (capacity:11KV,3.8MW)gas engines utilised,all are running in paralell. There are three transformer utilised,(1) 6.25MVA,3.3KV/22KV,Impedence voltage:6.7% used for two generator,both are 2.5MW(2)5.5MVA,3.3KV/22KV,Impedence voltage:7.2% used for one generator of 2.5MW & (3) 5.5MVA,11KV/22KV,Impedence voltage:7.8% used for one generator of 2.5MW.all generator breakers capacity of 1250Amps. Sir,I want the details of fault level calculation of generator,transformer individually & for whole system. If you require any information from me.feel free for contact me sir.pl.send the answer of my question as the earliest as possible.
Difference between Earthing Truck & Earthing trolly for HT panel
