how to calibrate a control valve?
- 7 Answers
- 61054 Views
- Reliance, Telecon Systems, I also Faced
- E-Mail Answers
Answer Posted / shefeek salim
In Control valve Calibration,its of two types;
1.Stroke Calibration
2.I/P Converter Calibration
1.Stroke Calibration
it means for the movement (opening and Closing) measurement of stroke through the Scale,from 0 to 100 percentage of valve Closing/Opening,according to the standard air pressure supply or milli amps supply(3 to 15 psi,4 to 20 mA)
2.I/P Converter Calibrtion
It is comparatively simple one,but it can be done in two ways,
2.1 Simulate the std 4 to 20 mA as input Check the output from the I/P
2.2 Simulate the std 4 to 20 mA to the I/P converter as input and measure the Control valve stroke movement through the scale(0 to 100%)
| Is This Answer Correct ? | 25 Yes | 0 No |
Post New Answer View All Answers
I want measure the volumetric flow of gas in waste heat recovery Boiler?Tell me how and which type of instruments required. Plz mail me:naba02222@gmail.com Sam please post the answer .
what is actual drum level and compensated drum level?
Where Can i take a SPI INtools training in Mumbai? In Rolta India Ltd to whom I should approach regarding of SPI INtools Training?
whatis range of marcury filled tempereture gague
what is a vortex flow meter,mass flow meter and electromagnetic flow meter.particular use of this.means in which condition particular meter is used.
NPN transistor, SCR, Zener diode, LED, Varactor diode, Vortex meter, RTD, Resistor, Crystal
1.what is the power consumption of three element drum level control in sugar industries? 2.how to reduce that?
Meaning of the following a. IOP- Manimum; b. IOP- Maximu,;
If fire would be inside the plant which fire detector is to detected the fire.
Can any one tell me what type of question asked for instrumentation and control interview panel??? pls mail ramashankar.goel@gmail.com
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
The company where I am working, their is rosemount 5400 series radar type level transmitter, it is meant to show level of filled tank, but along with the level it is showing temperature also, so my question is how a onon-contact type radar type level transmitter can show temperature even if it does not have any contact with the fluid?
What are different types of orifice plates?
For crude application in floating roof tank, how to calibrate a DP Transmitter? How is the floating roof weight considered?
find the kp ki kd from the transper function G(S)=29.44s+04707/1.5349s2+s
