Interested to Buy Any Domain ? << Click Here >> for more details...
I want to use 1/2 inch SS316 tube in my high pressure &
temperature (64 kg/cm2 & 500 deg C)after condensate pot in
pressure tranmistter.
1) Is it possible to use 1/2" ss316 tube in high pressure
and temperature line.
Tube manufacturer is local vendor.
2)On sarting the plant, We need to do system fluse that
time condesate is not in the condesate pot so steam is
directly contact with the tube. We have no exact
calculation to know our tube is ok or nor at this time.
pleae,reply.
- 1 Answers
- 5441 Views
- I also Faced
- E-Mail Answers
Answer Posted / carl_ellis
1) Tubing comes
- in different wall thicknesses and the pressure rating
varies with wall thickness.
- in different material grades of stainless steel. The
pressure rating can vary with material
Your vendor should be able to supply the rating of the
tubing as determined according to a national standard like
ASME B31.1 and ASME B31.1 Process Piping from which
allowable working pressures are calculated from an S value
of XX,XXX psi (YYY.YY MPa) for ASTM A269 tubing at –20 to
100°F (–28 to 37°C), as listed in ASME B31.3 and ASME B31.1.
A factor (different factor for different temperatures) is
used to calculate the reduced maximum pressure at elevated
temperatures.
An example is provided in the Swagelok tubing catalog on
pages 2 and 3 for their tubing (not your tubing).
http://www.swagelok.com/downloads/webcatalogs/EN/MS-01-181.PDF
You need to run the calculation for your vendor's tubing.
2) You need to refill the tubing and condensate pots with
water after the flush but before steam is applied, otherwise
the steam will damage the transmitter.
Carl Ellis
Measure First
64Kg/cm2 = 910 psig
500 Deg C = 932 Deg F
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
how do we commission inergen system?
Q1: Consider part of a control loop, which excludes the transmitter, consisting of a process, a controller and a control valve which may be represented by two dead times of 0.5 min each and three exponential lags of 0.8 min., 1.0 min. and 1.5 min. respectively. We wish to express this system as an overall first order plus dead time (FOPLD) model ie gain, time constant and process dead time. (We will see later that this is often done, to simplify controller tuning). For this exercise, gain is considered to be 1.0. (A) If the transmitter is a flow transmitter whose behaviour can be described by a dead time of 0.2 min. and an exponential lag of 0.5 min. in terms of the overall dead time and overall first order lag how can the system behaviour be approximated ? Overall dead time = Overall time constant = (B) If the transmitter is a temperature transmitter with a temperature sensor in a protecting well whose behaviour can be described by a dead time of 0.7 min. and an exponential lag of 15 min. how can the overall system behaviour be approximated now? Overall dead time = Overall time constant =
Explain the working of an electronic level troll.
How ejector(or)evactor air pump is working in thermal power plant?
what is metal of piston ring
how to calibrate corollaries (Mass flow meter)?
What is difference between radial vibration and axial vibration explain in detail .
my data card only does run in my mobile so how can change it that it run other mobile & computer and i can stor data in my data card
What is feed factor and its Importance in cement industry? How we can solve feed factor?.
May I have a brief note above the voltage barriers? Whats is the purpose? Please mail me if you've operational details, mail id: rajkumar.diice@gmail.com
how to calibrate and troubleshooting of leveltroll?
What is the use of GMV in turbine?
control panel design guidelines
Can Any body tell me about the Contact or Email id of any good Consultancy which help me to find a job in Instrumentation Field in India .I have Six years of Work Experience in the Same field.Please revert me back on shammi_gwalior@yahoo.com ?
How to calibrate displacer type level transmitter (chemtrol make )for level measurement in hotwell , LP & HP heater ?
