Interested to Buy Any Domain ? << Click Here >> for more details...
How to calculate the ups battery back up? give the formula.
- 15 Answers
- 111161 Views
- Cushman Wakefield, Ethio Telecom, Exide, MacLellan, Morgan Stanley, TATA, I also Faced
- E-Mail Answers
Answer Posted / sayyed fayyaz ahmed
Calculating the UPS and Battery Backup Time
Before calculating the Battery Backup, let us know a few
factors that vary battery backup.
For and UPS with 875Va we can us a maximum load of 640
watts 677Va we can us a maximum load of 540 watts
The main thing we should understand is that whatever may be
the UPS wattage the battery backup will not vary.
The battery backup will only vary depending on the battery
Ah and the Usage Load.
To calculate UPS backup, we have a simple formula.
UPS Backup = Battery Ah * (Volts/Load) * (1/Power Factor)
Example: Let us calculate the backup for a system UPS
Load is the usage power, suppose we are running a PC then
the load is around 300 watts
Power Factor varies for device to device, the average power
factor is 1.4
Voltage is the voltage of the battery.
For a single battery the voltage is 12v.
If the batteries are connected in a series Voltage = 12 *
no. of batteries.
Battery Ah is the battery ampere used for the ups,
System UPS battery AH is 7
Then Battery Backup = 7 * (12/300) * (1/1.4)
= 7 * (0.04) * (0.7)
= 0.19 hours
= 11.4 Minutes
Note: You can use the same formula for calculating the
battery backup for home UPS or an INVERTER.
| Is This Answer Correct ? | 19 Yes | 12 No |
Post New Answer View All Answers
What Maximam Gap Taibaar & Bush
Define average demand?
how is positive, negative, zero sequence is happen.. how is effect on 3 phase system
hi i will D.E.E.E.is completed pls send rrb diploma old qustion papaer sent in my e mail. i.d.
slipring induction motor starting time Lrs operating why lrs starting time lrs outer body didn't get shock
Is it required to do earthing in 2nd shop if earthed armoured cable is laid from 1st shop ?
1. What is differential relay? How it operates? 2.How to calculate the Short Circuit Impedance in Transformer? 3.What is the alternate solution for testing of polarity by using polarity tester while its milli ammeter does not works? 4. While testing the 33KV Busbar by using Hipot kit, what should be the test voltage we have to apply? 5. What is the procedure/activities to be taken to inject the current more than 2000A by using 2000A Loading Transformer? 6. Explain how you can give the overload setting to any Motor Protection Relay for a HT motors with formula and example? 7. Why restricted earth fault protection is needed? Why can’t differential Protection is sufficient? 8. What should be the minimum and maximum ohmic value for earthing? 9. Why DC Currents are not used in transformer? 10. What is the Frequency while we step up the voltage from 220V to 11KV? Is it possible? Explain it?
How grounding is different than earthings?
how calculate gd2 of ht motors
in the directional overcurrent and earthfault protection,normally we are setting the angle 45 deg lead for phase fault overcurrent and -45 deg lead for earthfault fro forward direction.but both the fault are operating on the same angle region only.why?how the relay will response?
how to find the torque of the single phase synchronous motor by doing an experiment
HOW TO SET THE EARTH FAULT SETTINGS IN ACB????????????
What is the high series capacitance winding on high voltage power transformer ?
what is dry and wet frequency withstand voltage? why & where it is used??
As per standard, transformer body earthing and other Equipment earthing (Equipment earthing) did not connect. but in LT side termination we are doing metal glanding in both side Transformer to PCC Panel through armoured cable, now X'mer body earthing and PCC Pane earthing (Equipment earthing) both are connect.is this safe for X'mer or other equipment?
