Interested to Buy Any Domain ? << Click Here >> for more details...
Diff between Earthed & Unearthed cable ?
- 1 Answers
- 4996 Views
- Torrent Pharma, I also Faced
- E-Mail Answers
Answer Posted / mds.1490@gmail.com
n 3phase earthed system, phase to earth voltage is 1.732
times less than phase to phase
voltage. Therefore voltage stress on cable to armor is 1.732
times less than voltage stress
between conductor to conductor. Whereas in unearthed system,
(if system neutral is not
grounded) phase to ground voltage can be equal to phase to
phase voltage. In such case the
insulation level of conductor to armor should be equal to
insulation level of conductor to
conductor.
For example for a 6.6kV ungrounded system, 6.6kV/6.6kV (UE)
class cable has to be used while 6.6kV/3.8kV (E) class
cables are adequate for solidly earthed systems. The
UE-class cable is
naturally costlier than the earthed class of cable.
| Is This Answer Correct ? | 2 Yes | 0 No |
Post New Answer View All Answers
how oltc works in rectiformers of higher rating (27 mva,200v dc,120kamps) please provide me full information with diaggram.
what happen when increase or decrease size of lamp,light.glass.
how point on wave controller works.
What is difference between start imitation and start interlock for 3 phase motor protection ?
Can clean earth cable be considered as low current cable
What are safety device in vcb and acb?
can anybody send me syllabus of rrb section engg (electrical). and also send previous question pepar...
There is air in a room . the top and bottom of the room are at constant temp. T1 and T2. DRAW THE temp profiles if a. T1 greater than T2 b. T1 less than T2
If there is major % of Voltage harmonics in the system, how can it be control or reduced?
at which voltage level arcing ground is occurs ??????????
A powerplant has 8 gensets operating in grid parallel mode. In one genset sometimes there is pf variation and kvar variation. The plant operates in pf mode. When this variation is observed the load is stable, voltage is also stable, freq and genset speed is also stable. How will you check the functioning of pf card. What shall be the ideal output vdc of the pfc, from there it is input to AVR?
static chagre
1)How much current can a 3-1/2 core 100 mm wire carry? 2)What are the special cables required for explosion proof wiring? 3)In case you do not have coal and salt for earthing, how can you achieve good temporary earthing? 4)One horse power single phase motor is more likely to get hot than a one horse power 3 phase motor. Is it true or false, if true why? 5)What are the different types of soft starters for large motors?please explain?
1)how to reduce the value of tan delta of trasformer and CB,bushing,CT&PT,CVT ? 2)how to reduce the resistance of CB contact and its operating time? 3)plz.....send me the project report on conditioning and monitoring of substation equipment on my email id (gusaiyogendra03@gmail.com)
(1)The demand for electricity , the amount of renewable generation available, the amount of fossil fuel generation available and the cost of the fossil fuel generation are shown in table below period(hrs) demand(MW) renewable (MW) fossil- fuel(MW) cost of fossil fuel(MW) 00.00 - 01.00 2000 1800 2000 30 01.00 - 02.00 2300 2500 2000 30 02.00 - 03.00 2500 2700 2100 45 03.00 - 04.00 2900 3100 2100 50 04.00 - 05.00 2700 2600 2500 45 05.00 - 06.00 2400 2000 2700 50 06.00 - 07.00 2200 1800 2000 36 07.00 - 08.00 2100 1600 2000 36 Assuming that the renewable generation incurs zero cost, determine an optimal generation schedule(specifying the amount of renewable generation and fossil fuel generation used in each period, the cost for each period and the overall cost for 8 hours.)
