Interested to Buy Any Domain ? << Click Here >> for more details...
Answer Posted / eid elatawy 01000470262
1.PM Preventive maintenance To check the instrument and do the needful to prevent any failure may be done in the future.
2.CM Corrective maintenance:to correct the function of the instrument.
3.RCM Reliable centered maintenance filter PM problems in the instruments to obtain the maximum performance of maintenance for example each PM we found problem in LTXX01 we will change the type of this Tx to improve the maintenance performance.
| Is This Answer Correct ? | 11 Yes | 2 No |
Post New Answer View All Answers
WHAT IS MEANT BY PROJECT MANAGEMENT STRATEGIES IN INSTRUMENTATION?
䑰ҕ䔈ҕ䖠ҕ䘰ҕ䛀ҕ䝐ҕ䟐ҕ䢐ҕ䥐ҕŹ
what is a good line as ic engineer as maintenance ,oc, project, calibration ,validation engineer?
We Have Two Field bus Pressure Transmitters of Different Sensor Range (I.E One is of Lower range and Another is of Higher Range).Is same Process Line. My Question is Can i provide Saturation Limit to my field Bus Transmitter as We can provide Saturation current limit to HART Instruments. As During Low Pressure Both Working OK ,But During High Pressure, transmitter with Lower sensor range Goes to Fault mode as Beyond its Sensor Limit it can Measure, So may I provide Saturation point Some where to Suppress This Fault during High Pressure.
What is eddy current? Describe the operating principle of proximity probe.
what is function of switch, and how is it work, explain with difination
How to decrease opening & closing time of on/off valve?
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
Can I calibrate the Electromagnetic Flow Meter on line and How.
Describe the function of Accumulator into the Pump
what is the procedure to callibrate temp controller ,pressure controller,etc. suppose a temp controller showing error 1.5 degree centigrate how can i minimize it.
WHAT ARE THE INSTRUMENTAL DIAGRAMSOF VALVES?
what different types of problems do occur while doing instrumentation commisioning and how to solve them? please explain in detail
we are using centum vp as monitoring with Dell precision work station T3600 but some times PC(s) are restarted automatically . how we can solve this problem? thanks
What are the interlocks we have to check during the start up of LP/HP compressor?
