why transformer rating in KVA ?
- 8 Answers
- 10005 Views
- Bhel, TATA, Voltage, I also Faced
- E-Mail Answers
Answer Posted / sunil kumar pandey
Because transformer rating depend on load (resist.,
inductive , capacitive) if transformer feed to resistive
load at unit PF. Then there rating is VX I X1=?
If feed to inductive load for e.g. PF .85 Then there
rating is VX I X.85., that’s why its rated at KVA, where k
is constant i.e. 1000.
| Is This Answer Correct ? | 6 Yes | 12 No |
Post New Answer View All Answers
1. A 380 / 220 V r.m.s. 3-phase 4-wire circuit carries loads of 8 + j8.1 ohm; 4 + j4.1 ohm; and 2 +j2.1 ohmin the three phases respectively. The length of the circuit is 100 m, and the resistivity of the phase conductors is 0.0005 Ω/m. The neutral conductor is of the same size as the phase conductors. a) Select a reference angle 0for the first phase. Then write down the three phase voltages in both polar format and complex number format. b) Make appropriate assumptions, and take temperature effects on resistance is insignificant. Calculate the currents in the three phases. (Note: Determine conductor resistance, and apply Kirchhoff’s Voltage Law) Based on the result, suggest a main switch rating for the circuit. c) Show your preferred direction of neutral current in a diagram, and then determine its value. (Note: Apply superposition principle, and Kirchhoff’s Current Law) Use its magnitude to show that in this circuit, the unbalanced load may increase the voltage drop in some of the phases. (Note: Also observe the common volt drip in neutral) State your assumptions, if there are any. d) Suddenly the neutral wire of the circuit is broken. Estimate the new currents in the first phase, i.e. Phase L1. State your assumptions, if there are any.
How convergengr of nr method is not dependent on selection of slack bus and how gauss siedel method depends?
how can get electrical c licence.now i am working in spining mill , transformer capacity 2750KVA. SANCTION DEMAND 2250KVA. PLEASE ADVISE ME . MY CONTACT NO 09944226823
what is the prosses for getting of 33kv licence (i have completed my engineering degree & working in 33kv substation for contract basis )????
what is the difference between the voltage of 5 volts capacitor and and 5volts battery?
What is the diffrence (Technical & Construction ) between CBCT & Normal CT?
we have two motors 1250kW,6.6kV to be coupled on the same shaft ,so please provide assistance for their synchronisation.
what is the diff. between x'mer , isolation x'mer & ultra-isolation x'mer ?????????????
I had applied for JE in PSEB, Can you pls send me the Question bank for related to my field
is this the formula of building wiring to get the main breaker.Watts/volts*.8%+higher motor*(25%)=ampere. yes or no or send the correct formula for building wiring.
what is Fan Control Cubicle
can we choose current transformer secondary, to calculate residual flux in a power transformer, so as its saturation is close to the saturation level of power transformer?
why would amp draw on neutral wire be as much as amp draw on the hot leg.
How cable from Kit-Kat to main switch, from starter to motor are designed?
132/6.6𝚔𝚟 𝚝𝚛𝚊𝚗𝚜𝚏𝚘𝚛𝚖𝚎𝚛 𝚗𝚎𝚞𝚝𝚛𝚊𝚕 𝚑𝚊𝚜 𝚘𝚗𝚎 𝚎𝚊𝚛𝚝𝚑 𝚙𝚒𝚝 𝚍𝚎𝚍𝚒𝚌𝚊𝚝𝚎𝚍. 𝙸'𝚟𝚎 𝚊𝚗𝚘𝚝𝚑𝚎𝚛 𝚝𝚛𝚊𝚗𝚜𝚏𝚘𝚛𝚖𝚎𝚛 𝚘𝚏 6.6𝚔𝚟/415𝚟 𝚌𝚊𝚗 𝙸 𝚌𝚘𝚗𝚗𝚎𝚌𝚝 𝚗𝚎𝚞𝚝𝚛𝚊𝚕 𝚝𝚘 𝚜𝚊𝚖𝚎 𝚎𝚊𝚛𝚝𝚑 𝚙𝚒𝚝 𝚊𝚜 𝚘𝚏 13/6.𝚔𝚟 𝚝𝚛𝚊𝚗𝚜𝚏𝚘𝚛𝚖𝚎𝚛?? 𝙸𝚏 𝙽𝚘.. 𝚃𝚑𝚎𝚗 𝚠𝚑𝚢??
