Answer Posted / saravananp
Plate earthing provids using copper plate (450mm x 450mm x
6mm). The area of the copper plate is high causing high
earthing value (Low resistance).
Instaling Method: The copper plate at the depth of 2 Mtr or
3 Mtr. The centre support provides using 40mm GI pipes,
funnel in top.The two numbers of 25mm x 3 mm copper flat
stamped from top of the GI pipe to copper plate to improve
the earth value. The salt, charcole to improve the
conductivity.
The materials using for plate earthing are as below:
1) Meshed Funnel
2) 40 x 300 x 6 mm copper earth pad
3) 25 x 3 Cu strip
4) Copper Rivit
5) 450 x 450 x 3 mm Cu plate
6) 8x25 mm bolt and nut with washer
7) 6x75 mm bolt and nut with washer
8) 40 mm GI pipe - 2.8 mtrs
9) 25mm dia x 200 mm length GI pipe with double end threaded
10) 40mm to 25 mm GI reducer
11) 1" Check nut(6mm thick)
12) Charcoal
13) Salt
14) 450 x 450 mm heavy duty SFRC chamber cover with frame
ersaravananp@gmail.com
Saravanan.P
| Is This Answer Correct ? | 6 Yes | 1 No |
Post New Answer View All Answers
how to calculate transformer load?
what is formula for zero phase sequence of nuetal earthing transformer of 6.6 kv
is the value of inductance depends upon the value of thitha in doubly excited machine??
What will happen if i replace a inductive proximity switch with photo sensor in a machine?
How grounding is different than earthings?
How to calculate the size of earth cable to earth the neutral of UPS ?
what is the difference between unarmoured & Flexible cable? How to identified?
In what condition the HT fuse breakes?
A 100KVA SINGLE PHASE TRANSFORMER 10000/200V,50HZ REQUIRES 300V AT HV SIDE TO CIRCULATE FULL LOAD CURRENT WITH LV SHORT CIRCUITED.THE INTAKE IS 1000W.THE % OF REGULATION ON FULL LOAD AT 0.8 PF LAGGING WILL BE HOW MUCH AND THE SECONDARY TERMINAL VOLTAGE ON 0.8 PF LEADING WILL BE
what is the use of expulsition protective gap in 11Kv line.
explain wiring system
hi all i like to know vat is power plot in control systems also i want to know abt latest trends in electrical & electronics
1- XC and the RC time constant are both measures of the reaction of C to a change in ____? 2-The power factor is a numerical ratio with a value between 0 and 1 equal to the ______________ of the phase angle. 3-When V and I are out of phase because of reactance, the product of V times I is called ______________ power 4-For _____________ inductors, the branch currents can be added algebraically. 5- The ______________ power in watts can be calculated as I^2R 6-Calculate XL with L = 30mH and f = 1kHz ( I have Xl=2piFL 2*3.141592653*1kHz*30mH =188 ohms Please check) 7-A parallel RL circuit has the values, R = 5kohms, XL = 5kohms. A voltage source of Vt = 10Vrms is connected in parallel to R and L. Determine the total current, It delivered by the voltage source Vt. 8-A series RC circuit has R = 1Mohm and C = 1microF. How long would it take for the capacitor to fully discharge if it is initially fully charged? 9-A circuit has real power = 300W and an apparent power of 500VA. Determine the power factor and phase angle. 10-The time constant for an LR series circuit is T = 0.1s and R = 10ohms. Calculate the inductance L.
how do you test tachos and servos
My load is 1635 KW. & current pf is 0.884, I have to improve it for 0.99.Please suggest what KVAR value is needed?
