what is the meaning of wet leg & where is it used?
- 1 Answers
- 11381 Views
- I also Faced
- E-Mail Answers
Answer Posted / devendra_kushwaha27
A process used to determine the differential pressure
present within a liquid-filled space.
The formula for determining the differential pressure
within a wet leg design is: d/p = h (SG)
Where: d/p = differential pressure, h = height of liquid
present, and SG = specific gravity
When the process vapors condense at normal ambient
temperatures or are corrosive, this reference leg can be
filled to form a wet leg. If the process condensate is
corrosive, unstable, or undesirable to use to fill the wet
leg, this reference leg can be filled with an inert liquid.
| Is This Answer Correct ? | 18 Yes | 0 No |
Post New Answer View All Answers
please send me some question papers of HPCL aptitude test ?? please send it to bipinb.28@gmail.com ...
What are the key features of a Distributed Control System? describing the various layers (sensor through to business system interfaces) as well as the hardware, software and security aspects of the DCS.
sir i m preparing for BARC but i am not getting any papers to prepare for this exam so please send me some sample papers to my i.d for the preparation of barc.
I WANT SECURITY PAPER MILL, HOSHANGABAD TEST PAPER.KINDLY SEND TO MY MAIL ID
sir, i preparing hpcl,ongc,barc,hal exams(instrumentation engg)pls send a placement papers
where cascade loop use ?
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
hi i am eswar i want to know the instrumentation interview questations for eil(engineers india ltd) i have applied for engineer post in eil please help in this.my mail id eswar310@gmail.com
Sir,I am going to sit for IOCL written test exam. recently.Can anyone tell me the name of 'Objective type Question Book on Instrumentation Engineering ' which will help me. Pl. mail to bidyut_71@rediffmail.com / bidyut.saha2008@indiatimes.com / bidyut.saha09@yahoo.in
send me model hpcl questions pleas..........my mail id mohideen.dharvesh@gmail.com
hi sir yhis is zahid ali i am preparing for the jspl at oct.4.please send me the recently updated sample paper.
DEAR SIR/MADAM MY NAME IS ARKAPROVA BHATTACHARYYA.I AM A FRESHER INSTRUMENTATION ENGINEER.CAN YOU PLEASE SEND SOME QUESTION PAPERS OF GRADUATE ENGINEER TRAINEE EXAM OF DVC(DAMODAR VALLY CORPORATION).MY EMAIL IDs ARE arka_aec@rediffmail.com.
hello can yoy pls send me previous papers of jindalpower and steel ltd.....'m from instrumentation..... mani1048@gmail.com
principle of dead weight tester ?
hello friends, can you please send me the model paper or question paper to be prepared for hpcl examinations????????? You can mail me at rahim_here@yahoo.com waiting for your reply........... help me .. plz.....
