what is difference between pressure and stress?
- 6 Answers
- 8377 Views
- MAHINDRA, I also Faced
- E-Mail Answers
Answer Posted / jet b
Pressure is the external force acting over a unit surface
area of a material.
Stress is an internal force acting over a cross sectional
area within the material.
It may also be thought of as the internal resistive
response of a material to the applied external pressure.
They both have the units of force / area.
| Is This Answer Correct ? | 3 Yes | 0 No |
Post New Answer View All Answers
Does the rate increase by experience or number of years worked?
How do you determine what suction pressure should be in r22 air conditioning compressors suction line?
CATIA:SPRING WITH SOME RADIUS AXIS
What are the causes of turbine vibration
1.how to Ask the result After the interview gone? 2.please send me the interview questions of unigraphics,IDEAS,solidworks,autocadd,and mechanical design. to my mail id austinsobanam@gmail.com
can someone explain tolerances on bolts what the symbols mean
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
How to calculate CFM in Compressure or Blower? EX. I hv Blower with 5hp motor.then how to calculate the CFM?
Dfine an ortographic drawing?
draw diagram of automobile,its working function,purpose of differential?
We select 10mm nominal thickness for Elip head of a pressure vesel. The minimum thickness after forming is 8.2mm. (Shell thickness is 8mm. The minimum thickness after forming is satisfied or not with UG-79 (d)(3) in ASME SECTION VIII, Div.1?
What do you know about DG ,A,B,C, D, Check and safety of generator.?
What are the advantages of gear drive?
What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls?
How to check temperature controller?
