Interested to Buy Any Domain ? << Click Here >> for more details...
If you don’t have coal, salt and copper, then how would you
earth your connection temporarily at a campus site?
- 2 Answers
- 5068 Views
- I also Faced
- E-Mail Answers
Answer Posted / udayak25
Then u can (1)connect earthing wire to the GI water
pipeline.
(2)or connect to building structural bars.
for these any how check once bcoz there may be
disconnection in bars or pipe.
(3) one more is take a bar of MS & burry it around 1ft below
GL, and
connect earth wire but be sure the soil should wet all time.
| Is This Answer Correct ? | 4 Yes | 0 No |
Post New Answer View All Answers
What is the reason behind current flow(20 A) in amain earth cable of an SMDB? Is cuurent flow(45A etc) through a neutral cable acceptable?
What types domain of laplace transforms? What behavior can laplace transform predict how the system work?
The specific heats of the gas at constant pressure and constant volume are respectively 1.0 kJ/kg K and 0.72 kJ/kg K; the value of R for the gas is
can some one clearly explain why -48 volt DC use in telecom site????
what is the profesional board for electrical engineer what is thepast and during construction for electrical engineering
i installed 100kva ups. what KVA genset they should provid in input side? plz any update formula or ans with reason.
what is meant by directional earth fault and non directional earth fault? describe both.
how can we make cable shedule for controll wiring ? which details must be required for it.?
What is the difference between electrical earthing and electrical grounding?
i am going to correct power factor of 1600kw induction motor,when i calculate capacitance of capacitor it is three time more in star connection than delta. if motor is star connected which connection i shall adopt for capacitors and reason for adopt this connection
How can claculate to attain the desired PF in the line ( HOW Much KVAR is required ) Pls Give the formula? Equate Petrochemical 0 1 how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec. 0 1 What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding? Equate Petrochemical 0 1 What is required of exietation to the alternater. 0 1 why star point of HT motor not earthed? Equate Petrochemical 0 1 Why we are getting low voltage in star connection? Equate Petrochemical 0 2 What's ND relay & it's functions? Equate Petrochemical 0 2 How instantanious short circuit current is calculated? its formula? Equate Petrochemical 0 2 What is servo Motor? What's the advantages of this motor over Induction motor? Equate Petrochemical 0 2 What is core CT & it's function? Equate Petrochemical 0 3 what is meant by star/delta voltages as 440/220 in a 3 phase induction motor, and why it should be connected on STAR IN 3 PHASE SUPPLY L & T 0 4 What is required of exietation to the alternater. KNB 1 23 what is the design voltage for 6.6KV 2000 KVAR HT capacitor? Consultancy 0 3 Pls explain about vfd control?Where it is used, Give some example? siemens 1 22 Please explain me abt PQ diagaram in the power sector. 0 9
what is Anti-pumping?
Why IR value of the (HT cable Plus synchronous motor) is less while individually having IR values in GΩ?
Why we are using only Dyn11 tranformer in distribution system but not using a Dyn1 in distributing system?why not and advantage and disadvantage in both
An automatic water heater is an example of which type of control system?
