Interested to Buy Any Domain ? << Click Here >> for more details...
Can neutral line also be use as a earthting for
distribution transformer, or we need separate earthing pit
forh the transformer?
- 1 Answers
- 5677 Views
- I also Faced
- E-Mail Answers
Answer Posted / ullas
in the distribution transformer the secondary star side
common point is earthed and taken it as a neutral terminal.
this neutral is earthed 4 place i one mile., in order to
keep the potential as zero volt..
there are so many distribution systems in india.
take the case of kerala, my state.
here we are using the TNCS System.
here phase line and neutral line are given to the consumer
by the supplier. the consumer shall provide an earth pit
for earthing his equipments.
in tamilnadu the TNEB provide additional earth line with
phase and neutral.
| Is This Answer Correct ? | 7 Yes | 0 No |
Post New Answer View All Answers
All tape of electrical questions Answers tape of motor transformer e.o.t crane
How can claculate to attain the desired PF in the line ( HOW Much KVAR is required ) Pls Give the formula? Equate Petrochemical 0 1 how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec. 0 1 What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding? Equate Petrochemical 0 1 What is required of exietation to the alternater. 0 1 why star point of HT motor not earthed? Equate Petrochemical 0 1 Why we are getting low voltage in star connection? Equate Petrochemical 0 2 What's ND relay & it's functions? Equate Petrochemical 0 2 How instantanious short circuit current is calculated? its formula? Equate Petrochemical 0 2 What is servo Motor? What's the advantages of this motor over Induction motor? Equate Petrochemical 0 2 What is core CT & it's function? Equate Petrochemical 0 3 what is meant by star/delta voltages as 440/220 in a 3 phase induction motor, and why it should be connected on STAR IN 3 PHASE SUPPLY L & T 0 4 What is required of exietation to the alternater. KNB 1 23 what is the design voltage for 6.6KV 2000 KVAR HT capacitor? Consultancy 0 3 Pls explain about vfd control?Where it is used, Give some example? siemens 1 22 Please explain me abt PQ diagaram in the power sector. 0 9
Why transformer used in UPS??
How many types of protection relays are there based on the characteristic?
-What should be minimum value of insulation resistance and maximum value of earth resistance at any electrical instillation and what is method of testing the same.
If a current -8+6sin6t is flowing three ammeter, one is a centre zero PMMC meter, one is true rms meter and one is moving iron meter. What are the reading of these three meter respectively?
regarding safety what would u consider the most important rules to observe when inspecting electrical equipment?
what is deffrence between squirral cage and wound rotor in IM?
what is the voltage rating of chiller unit sensors
How to calibrate or test an LT Air Circuit breaker 440 volts, 35 KA, 800 Amps ?
What aturn on methods of scr?
generally in LT and MV motors we are using 3.5Coresx16,25,35,50 etc cable for supply.although motors is earthed at two point and having all protection.then why we are using that 1/2 core for earthing the motors.while in HT cable we are using only 3core cable for motor supply.generally lt and mv motors are delta connected and ht motors having star connection.whethere it is having any relation with winding connection( star or delta).all motors i am talking about are dol only.can anybody solve my confusion.thanks...
Draw transformer phasor diagram.(full load,no load)
What Is Connection APFC Panel In Compony.
state the disadvantages of carbon filament???
