Interested to Buy Any Domain ? << Click Here >> for more details...
What accessories required to give the motor with given
circuits and do you know the ratings of those accessories?
- 4 Answers
- 31586 Views
- Hyundai, TCS, I also Faced
- E-Mail Answers
Answer Posted / pramod_wank
The answer of manish joshi is correct some correction as follows
1. RTD's: Resistance temperature Detectors : used to
measure the winding temperature , PT-100(2mA) is used in RTD
and
normally 6Nos can be used(In each winding 2nos RTD)
2. BTD's: Used to measure the bearing Temperature rise.
Normally 1pc/Bearing (In each side 2RTD used Drive side end
(BE) & non drive side end(NDE))the total 4RTD required
3. DTT's : Dial type thermometeres with contacts/without
contacts alarm trip.(DTT normally used for drive side end &
non Drive side end at max 250v,5A)
4. Space Heater: Used to remove moisture when motor starts
after a very long time where moisure is present in the
surroundings. ratings 240 V 1Ph.
5. SPM Nipples: for vibration monitoring (for drive & Non
Drive Side end)
6.Seperate terminal box for space heater(1ph,240v,300w).
7.Greasing Nipple for Drive & Non drive End.
8.Vibrating Sensor at drive side.
9.Main Terminal box to coonect the supply 415V AC.
10 Neutral terminal Box if required
11.Lifting Hook to lift the motor
12.Earting Bolt as per your electrical system.
| Is This Answer Correct ? | 17 Yes | 1 No |
Post New Answer View All Answers
Can we use BS 6651 and BS EN 62305 standards for computer room lightning ptotection in substation?
if flux and load static in dc motor and supply voltage increases 20% then what happened in speed
11kv/433v delta/star distribution transformer primary side full load Ht current is 83.33A in , but input side VCB rating 800A.why?
Two electric lamps 40 W, 220 V each are connected in series across 220 V. What is the power consumed by the connection?
what percent do you derate your copper wire when you change from copper buss to copper wire
H.t motor 6600 volt to same motor lt supply 440volt supply applyed to h.t motor to effect....
how to calculate transformer turn primary & secondary side 11kv to 420v
how pt is using
what is the difference between Central Battery System and UPS in applications and uses? and why UPS suitable for Computers and central battery for emergency lighting?
A cylindrical wire is compressed in length by 10%. The percentage decrease in the resistance will be?????
what is the diff. between x'mer , isolation x'mer & ultra-isolation x'mer ?????????????
(1)The demand for electricity , the amount of renewable generation available, the amount of fossil fuel generation available and the cost of the fossil fuel generation are shown in table below period(hrs) demand(MW) renewable (MW) fossil- fuel(MW) cost of fossil fuel(MW) 00.00 - 01.00 2000 1800 2000 30 01.00 - 02.00 2300 2500 2000 30 02.00 - 03.00 2500 2700 2100 45 03.00 - 04.00 2900 3100 2100 50 04.00 - 05.00 2700 2600 2500 45 05.00 - 06.00 2400 2000 2700 50 06.00 - 07.00 2200 1800 2000 36 07.00 - 08.00 2100 1600 2000 36 Assuming that the renewable generation incurs zero cost, determine an optimal generation schedule(specifying the amount of renewable generation and fossil fuel generation used in each period, the cost for each period and the overall cost for 8 hours.)
which type of stability limit is higher,steady state or transient? why?
Good morning: I'm looking for some informations about the OLTC or the LTC: I wont to know what the function of the tie-resistor in during the operation of reversing/coarse operation Cordially
oltc of a transformer, how it works? and what are the equipment consist of describe briefly?
