Company Name Starts with ...
#  A  B  C  D  E   F  G  H  I  J   K  L  M  N  O   P  Q  R  S  T   U  V  W  X  Y  Z

  • Educomp interview questions (4)
  • Educomp technical test questions (1)



Educomp Interview Questions
Questions Answers Views Company eMail

how to count number of 3's in 100

982

Post New Educomp Interview Questions



Un-Answered Questions

what type of motor used to move a 1 ton gate? and relate ratings with load.

549


which type of casting enforces type safety

2445


why do u want to join bpo sector

851


How do you import payscale data from non SAP to SAP?is it through LSMW or any other way is there?

2261


how retrive the video file in php using video tag

723






What are the differences between Structural Patterns and Morphological Strutural Element?

1456


Explain the difference between record occurrence and record type?

601


What is DOM?

999


what is the reason if a supply air grill located top of the glass and glass is getting sweated.become like mist.

966


hi i am siva icompleted m,sc in organic chemistry in 2008&working as alecturer can u send me the interview qusetions with answers . i expected that i got 135 - 140 marks is there any chance to get selection my interview is on may 7th 2010

801


How to get DLL function parameter listings ?

831


sir/ma'm im doing my msc in biotechnology.im concern that can go for phd in genetics? and how?? plz help me in this..thank you

982


2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand

911


(1) In turbine, what does term CDP, NI, NH, HSSOC, means. (2) What is the purpose of LO overhead tank in turbines.(3) An equipment is certified for EEX, IA, IIC,T6, what do you under stand by this.(4) what is SURGE, and how it is prevented, what is the purpose of bypass valve across AS valve.(5) Give 2 application of quartz crystal used for process parameter measurement.(6) what is meant by cold float of compressor shaft. (7) state four different types of flow measurement. For gas flow measurement mmscfd is the common unit. Expand the unit and specify significance of word S in the unit.(8) what is meant by Gap voltage, in vibration measurement. Normally how much Gap voltage is set and state the reason.(9) what will the new flow factor if D/P transmitter is Re-Ranged from 25” wc to 50” wc.(10) what is the usage of QDV & Volume booster.

2390


how the speed of the gets motor regulated. does it draw the same current on the all speed level.

714






Educomp Interview Questions
  • OOPS (1)
  • C Sharp (1)
  • Engineering AllOther (1)
  • Accounting AllOther (1)
  • General Knowledge_Current Affairs (1)