what is the procedure for auto tune in masoneialn 12300 series displacer type transmitter?
- 1 Answers
- 1707 Views
- I also Faced
- E-Mail Answers
Answer Posted / Mr Rajesh Kumar Meena
The procedure for auto-tuning a Masoneilan 12300 series displacer-type transmitter involves several steps:
1. Connect the transmitter to the process and ensure that it is properly isolated from ground potential.
2. Initialize the transmitter by following the manufacturer's instructions.
3. Set the auto-tune parameters, such as the initial gain, damping ratio, and filter settings.
4. Start the auto-tune process by activating the auto-tune function on the transmitter.
5. Allow the auto-tune process to complete. During this time, the transmitter will measure the process response and adjust the tuning parameters accordingly to achieve optimal performance.
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
DEAR SIR/MADAM MY NAME IS ARKAPROVA BHATTACHARYYA.I AM A FRESHER INSTRUMENTATION ENGINEER.CAN YOU PLEASE SEND SOME QUESTION PAPERS OF GRADUATE ENGINEER TRAINEE EXAM OF DVC(DAMODAR VALLY CORPORATION).MY EMAIL IDs ARE arka_aec@rediffmail.com.
i hav applied for the post of engg. in iocl so please require the past test papers fro instrumentation engg please please help me and send me the papers or tell me the pattern and type of ques asked in examination......
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
any body please send me the old question papers of ongc test.
plz you help about Que paper of mahagenco previous your,any model paper relad to it{maharastra power genration}
I am manjunath having exp in maintenance of chemical plants,know i want to do a design course INTOOLS,after doing design course can we get jobs in design field.sinve i dont have design exp..
sir i m preparing for BARC but i am not getting any papers to prepare for this exam so please send me some sample papers to my i.d for the preparation of barc.
Punj lloyd is coming in our Jadavpur Universtiy campus for campus placement. Please send me some hints about the writtend exam. My email id is subratafriends@gmail.com
any body who gone thru recent iocl interview.INSTRUMENTATION questions. I need.
sir, i preparing hpcl,ongc,barc,hal exams(instrumentation engg)pls send a placement papers
principle of dead weight tester ?
Can any one tell me what type of question asked for instrumentation and control interview panel??? pls mail ramashankar.goel@gmail.com
send me model hpcl questions pleas..........my mail id mohideen.dharvesh@gmail.com
Can any one send me IOCL instrumentation question papers.. i dont know the pattern of the questions and what to prepare can any one help me on this .. my email id is anwarnishil@gmail.com
give me all the details about the interview and which type of question being asked
