Interested to Buy Any Domain ? << Click Here >> for more details...
How much earthing require for h.t.22 k.v. cable in coming side
& out going & 22 lighting arrest or,22 k.v.D.o. &
A.B. switch.
- 1 Answers
- 3229 Views
- I also Faced
- E-Mail Answers
Answer Posted / tejeswara rao paidi
The earthing requirements for a high tension (HT) 22 kV cable, lighting arrestor, disconnecting switch (D.O.), and air break (A.B.) switch are governed by specific standards and guidelines.
In India, the **IS: 3043 - 1987** standard provides the **Code of Practice for Earthing**¹. This standard outlines the general principles and detailed methodologies for designing and implementing earthing systems for electrical installations. It includes factors such as the resistance of the electrode, contact resistance between the electrode and the soil, and the resistance of the soil from the electrode surface outward¹.
For specific equipment like a 22 kV cable, the guidelines for use of underground cable systems and overhead conductor systems by the Central Electricity Authority could be referred².
However, the exact earthing requirements can vary based on factors such as the type of installation, soil resistivity, fault current levels, and safety considerations. Therefore, it's recommended to consult with a qualified electrical engineer or the relevant electrical authority for the specific earthing requirements for your installation.
Please note that this information is based on general guidelines and standards, and may not be applicable in all situations or jurisdictions. Always consult with a qualified professional or the relevant authorities for specific advice.
Source: Conversation with Bing, 28/1/2024
(1) Indian Standard: CODE OF PRACTICE FOR EARTHING - Law.Resource.Org. https://law.resource.org/pub/in/bis/S05/is.3043.1987.html.
(2) GUIDELINES FOR USE OF UNDER GROUND CABLE SYSTEM AND OVERHEAD CONDUCTOR .... https://cea.nic.in/wp-content/uploads/2020/04/b.pdf.
(3) MATERIAL SPECIFICATIONS CELL - महावितरण. https://www.mahadiscom.in/supplier/wp-content/uploads/2020/01/Metering-Cubicle-1122-kV33kV-29.08.2019-FINAL.pdf.
(4) TECHNICAL SPECIFICATION FOR XLPE POWER CABLE - महावितरण. https://www.mahadiscom.in/supplier/wp-content/uploads/2018/08/HTXLPESPEC2006.pdf.
(5) TECHNICAL SPECIFICATION FOR 33/132/220 KV H.T. XLPE POWER CABLE - OPTCL. https://optcl.co.in/writereaddata/Tender/150619110614E31-33-132-220KV_XLPE_CABLE_SPEC_12042019.pdf.
if any doubts regarding technicality refer the url mentioned
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
Why do we use center tap transformer that used with portable tools
what is mind in cable
what is gridrotor resistance starter
what is difference between speed mode and torque mode in motor?? explain in simple words please.
formula for calculation of switchgears(i.e. contactor, fuse, cb, relay etc.), if load current is given?
what are the different methods for the starting of a synchronous motor.
What is meant by stator?
How i can decide that HVDC line is best for transmission.
What is voltage ratio of a transformer?
what is the purpose of shading ring or shading coil in electrical equipments.
How 48-relay (incomplete sequence) functions?
what is earthing transformer? draw the winding dia.of earthing transformer.
In Dyn11 power transformer if any one of the 3 phases connected to earth in star connected side then please explain effect of the current flow in delta connected side of transformer.(In this case if one phase is shorted to ground in star connected side then we observe the current flow in two phases only not three phases in delta connected primary side. Please explain why it is so?)
checking procedure of capacitor based motors.used in fans etc?
WILL SCHNEIDER MAKE ACB(MASTERPACT)TRIP ON REVERSE POWER?
