Interested to Buy Any Domain ? << Click Here >> for more details...
PETROLEUM ENGINEERING - QUESTION 25.3 : Liquid octane has a density of 703 kilograms per cubic metre and molar mass of 114.23 grams per mole. Its specific heat capacity is 255.68 J / (mol K). (a) Find the energy in J needed to increase the temperature of 1 cubic metre of octane for 1 Kelvin. (b) At 20 degree Celsius, the solubility of liquid octane in water is 0.007 mg / L as stated in a handbook. For a mixture of 1 L of liquid octane and 1 L of water, prove by calculations that liquid octane is almost insoluble in water.
- 1 Answers
- 2101 Views
- I also Faced
- E-Mail Answers
Answer Posted / kangchuentat
PETROLEUM ENGINEERING - ANSWER 25.3 : (a) 1 cubic metre of liquid octane has 703 kilograms or 703 kilograms x mole / (0.11423 kilograms) = 6154.25 mole. Energy needed = [ 255.68 J / (mol K) ] x (6154.25 mol) K = 1573518.64 J where K is the unit symbol for Kelvin and mol is the unit symbol for mole. (b) Density of liquid octane = 703 kilograms per cubic metre = 0.703 grams per cubic centimetre = 703 g / L. There is 0.007 mg = 0.000007 g or 0.000007 g x (1 L / 703 g) = 0.0000000099573257 L of liquid octane in 1 L of water. With negligible amount of liquid octane in 1 L of water, octane is considered insoluble in water. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
Explain the procedure to estimate the friction factor involved in heat exchanger tubes?
Hi, I am in need of interview questions from Engineers india limited in chemical engineering.if any one has kindly post it to me soon.
What is an effective means of removing silicon from aluminum?
Explain what are some typical applications for glass-lined reactors?
What is the basic difference between dispersion & distribution in any polymer blend or alloy??
sir,please give me some exam paper for referance. Thanks & Regards,
How can we derive power factor equation p=vi cos phi?
What is vapour flooding and liquid floodin in distillation?
Explain what are the design considerations for a piping system for the transfer of slurries?
How does hollow shaft impeller works? Does it based on principle of pitot tube?
X is strong but has a very low density (1% of traditional earth materials.) and hence light weight. It is a recyclable material. The compression behaviour of X is strain rate dependent. Higher strain rates result in higher initial modulus and higher compression strength. It can also withstand unlimited number of cycling loading provided the repetitive loads are kept below 80% of the compressive strength. The internal structure of the material includes air-traps which make it poor heat conductor. X is non- biodegradable and chemically inert in both soil and water. Most acids and their water solutions do not attack it; however strong oxidizing acids do. Solvents which attack X include esters, ketones, ethers, aromatic and aliphatic hydrocarbons and their emulsions, among others. It does not support bacterial/fungal growth as well .It also has significant acoustic properties and effectively reduces the transmission of airborne sound. X is combustible and should not be exposed to open flame or other ignition sources. Combustion products are carbon monoxide, carbon dioxide, water and soot. Long-term exposure to sunlight causes yellowing and a slight embrittlement of the surface due to ultraviolet light. X is able to withstand the rigours of temperature cycling, assuring long-term performance.
What type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited npsha (net positive suction head available)?
What is the import procurement cycle?
What are the steps required to design a vapor-liquid separator or flash drum?
How is plate heat exchangers used in an ammonia refrigeration system?
