Interested to Buy Any Domain ? << Click Here >> for more details...
How to calculate tonnage for embossing or serration washer?
- 1 Answers
- 2520 Views
- IIS, I also Faced
- E-Mail Answers
Answer Posted / mayur bachhav
Please help me to find the answer
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
Hey guys anyone plzzz tell me the syllabus for Vizag Steel Plant (IT & Mechanical Streams)........ And Aslo plzz send the materials or previous papers of vizag Steel Plant Management Trainees for both IT & Mechanical Streams......... plzzzzzzz......... Plzzzzzzz
difference between aerofoil meter and orifice meter
I HAVE SELECTED INTERVIEW FOR GOVT POLYTECHNIC LECTURERS.I DONT KNOW ANYTHING.PLZ HOW INTERVIEW WILL GO AND WHAT QUE'S SUPPOSE TO ASK ABOUT SUBJECT.PLEASE SEND QUE'S AND ANSWERSTO MAIL OR CALL THIS NO:9966924990.PLZ HELP ME.
Greetings This question is about hydraulics and I request an expert to answer it. A simple hydraulic machine is made up of two heads, a larger one with a larger force inside a wider pipe and a smaller one with a smaller force inside a smaller pipe in width as in the second picture on this link: http://science.howstuffworks.com/hydraulic1.htm The question is this: what happens if the smaller head and the smaller force doesn’t exist but the smaller pipe is high enough to take all the liquid? For example the larger head is 1.00 sqr metre and can go down 1.00m under a weight of 100.00kg. The cross sectional area of the smaller pipe is 0.001 sqr metre. Now when the larger head goes down 1.00m, how high the liquid from the wider pipe can go into the smaller pipe of the cross sectional area of 0.001 sqr metre? Regards
What causes cylinder liner-wear down?
What is a mechanism?
• Why not 4 phase & 5 phase
what is the actual difference between casting and moulding? explain pressure die casting process?
2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand
Which are the sheets of metals?
Anybody please send me the papers of the reliance exam (apti and tech) so that i can go through it) mail me at raminder_verma@rediffmail.com
"What do you do when in your duty, ME alarm oil mist detect high density?"
plz send me paper of mppgcl 2008 or experience posted by any candidate
How can the reaction of support of a frame be evaluated?
should cutouts made in main header of metal ducting be deducted from duct measurement.
