How will you change the action of a control valve?
- 1 Answers
- 3474 Views
- CCIE, I also Faced
- E-Mail Answers
Answer Posted / morsli
you have in positionner the direct and reverse action ,you have only to commutate to direct action means when the signal fron the controller rise the out put of the positionner will rise also ,in same direction 4-20 ma signal to i/p positionner the signal will be 3-15 psi from the positionner..
but in reverse action when the signel from the controller increase the out put of positionner decrease reverse action 4-20 ma signal to i/p positionner the signal will be 15-3 psi from the positionner.
sincerly
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
pls suggest suitable MOC of diaphragm for pressure measurement of UREA grade solution service fluid.
i hav applied for the post of engg. in iocl so please require the past test papers fro instrumentation engg please please help me and send me the papers or tell me the pattern and type of ques asked in examination......
hello can yoy pls send me previous papers of jindalpower and steel ltd.....'m from instrumentation..... mani1048@gmail.com
give me all the details about the interview and which type of question being asked
please any body have most important data for study for saudi aramco test of instrument QC thanks email shahnaveedullah@gmail.com
sir i m preparing for BARC but i am not getting any papers to prepare for this exam so please send me some sample papers to my i.d for the preparation of barc.
sir, i preparing hpcl,ongc,barc,hal exams(instrumentation engg)pls send a placement papers
hi i am eswar i want to know the instrumentation interview questations for eil(engineers india ltd) i have applied for engineer post in eil please help in this.my mail id eswar310@gmail.com
Good evening all I need a small favour regarding reliance paper i wanna probable sample papers(e&i) of reliance. if any of u have any idea about dis then plz mail me back.i belongs to electronics and instrumentation engg.so i need e&i papers. thanking u....
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
can any send me a forbes marshall dtron 316 manual
hye SAM acn u send your e mail id, so that i can solve my query through e mail?
please send me some question papers of HPCL aptitude test ?? please send it to bipinb.28@gmail.com ...
DEAR SIR/MADAM MY NAME IS ARKAPROVA BHATTACHARYYA.I AM A FRESHER INSTRUMENTATION ENGINEER.CAN YOU PLEASE SEND SOME QUESTION PAPERS OF GRADUATE ENGINEER TRAINEE EXAM OF DVC(DAMODAR VALLY CORPORATION).MY EMAIL IDs ARE arka_aec@rediffmail.com.
sir, give me placement papers and interview quistion of birla group company of copper.
