Question 29 – For a Vernier scale that consists of 0.11 cm per section, estimate the length on actual standard ruler of 0.1 cm per section for 2.39 m and 0.91 m.
- 1 Answers
- 1735 Views
- I also Faced
- E-Mail Answers
Answer Posted / kang chuen tat (malaysia - pen
Answer 29 : For 2.39 m, length on standard ruler = 2.39 - 0.99 = 1.4 m. For 0.91 m, length on standard ruler = 0.91 - 0.11 = 0.8 m. The second decimal numbers for both Vernier scale and standard scale should be the same. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
For what ration of Lengh/Dia. of tank (Jacketed tank), maximum heat transfer area is available?
What is an effective means of removing silicon from aluminum?
I am a Diploma Chemical Engineer by Nirma Uni; and BEng (Hons) Energy & Environmental Engineer by Napier Uni; Edinburg, UK. HPCL chemical engineering test will held on 14th July,09. So, Please send me some previous chemical engineering papers Objective types Or material to give the test.
What steps can be taken to avoid stress corrosion cracking (SCC) in steel vessels used for storing anhydrous ammonia?
What is the use of gear pumps in motor?
Explain how is waste heat boilers categorized?
how will we calculate the heat of formation through electron...??
how we can find solubility of liquid in amyl alcohol and relative solubility of amyl alcohol
X is a solid having a white colour at room temperature. It has a density about 2g/cc. Although it has melting point near 325 degree Celsius, its properties start degrading above 260 degree Celsius. The coefficient of friction is very low about 0.1. It has very good dielectric properties especially at higher radio frequencies. It has a very high bulk resistivity. It is chemically inert. It is also resistant to van der Waals force. It is hydrophobic as well as lipophobic. Creep or ‘Cold Flow’ has been observed in X.
What kind of concerns is associated with temperature pinch points in condensers?
MY generator water cooler inlet line height - 11 mtr inlet water line height - 7 mtr water come into the line from overhead tank, O/H tank height - 20 mtr the first tapping in the inlet line is 2" line which down to 4 mtr level plateform., second tapping in inlet water line goes to a pump 6" line installed at 4 mtr level plateform, pump capacity 200m3/hr, head- 30 mtr, hp-40. the outlet of pump of 6" water line connected to a header of 6 mtr long of 6" line, on this header the six tapping are connected, 4 nos. 3" line goes to 11 mtr height water cooler the pressure of the line is 0.15 to 0.25 kg/cm2, 2" and 4" pipe line connected to a cooler at 4 mtrlevel plateform. my question is, at 11 mtr height level the quantity of water and flow is not sufficient for my cooler, the temp. of cooler is rises much more. you are requested to suggest the modification of pipe line/ pump for take more water flow and pressure (desired pressure is 1 kg/cm2)
Explain under what circumstances are vortex flowmeters the most accurate?
hi i need cpcl written exam question papers if anybody pls help me
What are some factors to consider when trying choosing between a dry screw compressor and an oil-flooded screw compressor?
could anyone send me model question papers or outline of graduate trainee(chemical engg) post?
