Interested to Buy Any Domain ? << Click Here >> for more details...
HELLO FRENDS ,, I M IN THE MIDST OF TROUBLE .. JUST LITTLE HELP ME...
SUPPOSE ,, I HAVE A CLOSE VESSELE TANK ( HEXANE MEDIA ) ,,
I M USING ROSEMOUNT 2051 DPT FOR LEVEL APPLICATION ..
ITS CALIBRATE RANGE IS.. . 0 TO 950 MMH20 ..I DID CALIBRATED DPT WITHOUT
REMOVING IMPULSE LINE OF HIGH AND LOW TAPPING.. & WITHOUT DISTURB 3 WAY
MANIFOLD..!!!
BUT ,,, DURING CALIBRATION I SELECT RANGE BY HART LRV IS 900 MMH20 & URV
IS 1300 MMH20 ,, BUT ,TANK LEVEL SOMETIMES 100 % AT 1100 MMH20 ,
SOMETIMES 1300 MMH20 ..IN THIS CONDITION .. WHOLE LOOP FAILED ,, MAIN
THING IS THAT ,, HOW TO CUSTOME RANGE SELECT ?? AND IF I USED RANGE OVER
THE ORIGINAL CALIBRATE RANGE ,,,THEN WHAT ERROR WILL BE COME ??? HOW TO
ZERO CALIBRATION OF DPT... HOW TO ZERO TRIM BY MANIFOLD ?? AND FOR TANK
LEVEL PURPOSE ... WHICH UNIT I CAN USE ??? IS THERE ANY CALCULATION OR
CALIBRATION .. IF YEH .. THEN PLZ JUST GIVE ME CALIBRATION STEPS FOR DPT..
THANKS YOURSSSSSSS
- 1 Answers
- 4525 Views
- Torrent Pharma, I also Faced
- E-Mail Answers
Answer Posted / carl_ellis
There is insufficient information to determine what the
correct range of the transmitter should be.
1) Is there a capillary with remote seal on either side of
the DP xmtr? If so describe in detail.
2) Is the DP xmtr mounted directly on the lower flange? If
not how high above and below the lower flange (tap) is it
mounted?
3) Is the DP xmtr high side connected to the lower flange (tap)?
4) Is the low side a dry leg or wet leg?
5) What is the specific gravity of the material in the tank?
6) If the low side is a wet leg, what is the specific
gravity of the fill fluid in the wet leg?
7) What is the elevation distance from the lower flange and
the maximum level?
8) what engineering units are used for level ? mm H2O?
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
Please send me the sample question of Instrumentation of hpcl/iocl exam. my mail id hihi_kiholo@rediffmail.com
Explain working principle of lvdt?
why is not useing in boiler skin thermocople
how to do dynolab wind speed sensor loop test, how to simulate value,i have simulate mA 4-20mA but not responding in DCS faceplate, please kindly advice me any one.
I am teja. I am studying Msc(tech) Electronics and Instrumentation (3years course) in Andhra university. But my course is not recognised by UGC and AICTE. Please tell me the job opportunities after this course. And i fineshed PLC course in IGIAT ,Vizag.Also complted my short term coure in SCADA, Seimans WinCC in ATI,Hyd.After Msc can i join Mtech for good job? or phd. How i can get good job in INdustrial Automation Side. Please give replay.Because this is my life matter.
hi sir yhis is zahid ali i am preparing for the jspl at oct.4.please send me the recently updated sample paper.
Explain the use of hair spring in the pressure gauge.
1.what is the power consumption of three element drum level control in sugar industries? 2.how to reduce that?
WHY THE DEGREE OF VALVE PLUG AND VALVE SEAT IS SLIGTLY DIFFERENT I CONTROL VALVE TRIM DESIGN
How can test or measure the probe and extension cable to identify if the problem at the probe or cable or at the driver it self? (pleast notify the measuring method)
Can Any body tell me how to check Modbus Settings in ER300N L&T trivector meter?
what is sil (safety integrity level
what is the procedure for auto tune in masoneialn 12300 series displacer type transmitter?
Can u tell me the principle of the tc,rtd,level switch,pressure switch ,transmitter(pr flow level temp.),vibration...plz
Why not come out analog output in ABB EL3020 when display show correct value
