1.In which princeple DP transmeter works?
2.Why UPS system is use for DCS?
3.How drum lvel controller works?
4.What is the difference between glob valve and gate valve?
5.How axial shift probe work & in which princeple it works?
- 1 Answers
- 8603 Views
- Luberef, Qatar Gas, Reliance, I also Faced
- E-Mail Answers
Answer Posted / mahalingam
1.The flow meters are followed by Bernoulis therom, In the DP the flow is direct proportional to the square root of flow.
2. The use of UPS to the DCS is, the DCS request un interrupted power to continue its operation. During the time of operation if the raw power supply not be available then the entire system connected with the dcs will shutdown its operation.
3. Drum level to be controlled via three element control. feed water flow, steam flow & drum levels are the control variable.
4.Normally globe valves are used in the low pressure drop with steam,Gas, hot water application where the high accurate flow is required. whereas the gate valve gives the larger pressure drop and more flow process mediums like juice and slurry applications.
| Is This Answer Correct ? | 5 Yes | 2 No |
Post New Answer View All Answers
What are the key features of a Distributed Control System? describing the various layers (sensor through to business system interfaces) as well as the hardware, software and security aspects of the DCS.
DEAR SIR/MADAM MY NAME IS ARKAPROVA BHATTACHARYYA.I AM A FRESHER INSTRUMENTATION ENGINEER.CAN YOU PLEASE SEND SOME QUESTION PAPERS OF GRADUATE ENGINEER TRAINEE EXAM OF DVC(DAMODAR VALLY CORPORATION).MY EMAIL IDs ARE arka_aec@rediffmail.com.
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
Can any one tell me what type of question asked for instrumentation and control interview panel??? pls mail ramashankar.goel@gmail.com
please send me some question papers of HPCL aptitude test ?? please send it to bipinb.28@gmail.com ...
sir, i preparing hpcl,ongc,barc,hal exams(instrumentation engg)pls send a placement papers
What is the Working principle of Dozing valve?
hye SAM acn u send your e mail id, so that i can solve my query through e mail?
any body who gone thru recent iocl interview.INSTRUMENTATION questions. I need.
Question on maha cement
hi i am eswar i want to know the instrumentation interview questations for eil(engineers india ltd) i have applied for engineer post in eil please help in this.my mail id eswar310@gmail.com
plz you help about Que paper of mahagenco previous your,any model paper relad to it{maharastra power genration}
hi sir yhis is zahid ali i am preparing for the jspl at oct.4.please send me the recently updated sample paper.
can any one tell me when ongc placement test and its forms is available????/ pls tell me if u know
give me all the details about the interview and which type of question being asked
