Interested to Buy Any Domain ? << Click Here >> for more details...
while we select CT, why the CT ratio is divided by 5??
ex:250/5,15VA,CLASS-1 CT.Why it is divided by 5??Help me please
- 2 Answers
- 5154 Views
- I also Faced
- E-Mail Answers
Answer Posted / velappan
it is not divided by 5
the primary current is 250A and secondary current is 5A in this case and 15VA is burden we connected on secondary
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
WHAT IS DEAD END IN PROTECTION?
In AC if the direction of current keeps reversing every half cycle, how does it propogate through the transmission lines?
The series field winding has low resistance while the shunt field winding has high resistance. Why?
Lt motor sfu flashing reasons?
Name the component u would expect to find in a switchgear assembly?
We have 250 KW x 2 motors, which are load from 25% to 100% varying load in every minute , so how can we compansate the power factor. pl give your opinions on the above subject.
I HAVE A INCOMING 100A MCCB TPN 25KA, CABLE LENGHT OF 80M 70MM CABLE SIZE FROM MAIN SUBBOARD TO NEW DB.BASE ON THE FAULT LEVEL SETTING OF 45KA.I WOULD LIKE TO FIND OUT 25KA ENOUGH KA. APPRECIATE IF SOMEBODY CAN ASSIST ME WITH FORMULA FOR THIS. FRM: JEFF
why 1.7Uo for HV cable Hi pot test?IE standard why?
how to select fuse rating for a 3-phase motor ???
What are the advantages and disadvantages of open loop control system?
What is the requirement of grounding the neutral of single phase generators on load? If the neutral is not grounded, what will be the effect?
Whether IP65 enclosure box blocks ventilation if driver for LED have to enclosed inside IP65 box
TRAFO 1. WHY BREATHER IS USED. 2. WHY OIL GOES DOWN IN CONSERVATOR TANK. 3. WHY WE ARE TAKING OIL SAMPLE TAKING FROM BOTTOM OF TRANSFORMER. 4. HOW TO CHECK IR VALUE OF TRANSFORMER. 5. WHY OLTC HAVING BUCHHOLZ TRIP ONLY; WHY NO ALARM. 6. OFF LOAD TAP CHANGER OPERATION PROCEDURE. 7. TR. SHUTDOWN / ISOLATION PROCEDURE. 8. WHEN THREE TRS. IN PARALLEL, ONE TR. IS NOT SHARING THE LOAD – WHAT IS REASON AND WHAT YOU WILL DO. 9. WHY TR. HAS OLTC IN HV SIDE. 10. WHAT IS % IMPEDANCE. 11. WHY TR. RATING IN MVA. 12. WHAT IS VECTOR GROUP IN TR. 13. CONDITION FOR PARALLEL OPERATION OF TRS. 14. WHAT IS TERTIARY WINDING. WHERE IT WILL BE. 15. IF TR. TRIP ON BUCHHOLZ OR TAP CHANGER RELAY, WHAT YOU WILL DO. 16. DIFFERENCE BETWEEN OIL TEMP. AND WINDING TEMP. PROTECTION 17. HOW WINDING TEMP. IS MEASURED IN CAST RESIN TR. 18. DIFFERENT TYPES OF FAULTS IN TR. Trafo - Page-1 of 2 19. WHAT HAPPENS WHEN TR. CHARGED FROM LV. 20. WHAT WILL YOU DO IF MEGGER READING SHOWS ZERO BETWEEN LV WINDING AND EARTH. 21. CAN WE INTERCHANGE BUCHHOLZ RELAY OF MAIN TANK AND OLTC TANK. 22. IF THE LINE BETWEEN BREATHER AND CONSERVATOR TANK 23. LOCKED, WHAT WILL HAPPEN DURING LOAD CYCLE. 24. WHAT IS THE FUNCTION OF OIL SEAL IN BREATHER. 25. WHAT ARE LOCATIONS FOR BUCHHOLZ RELAY FIXED IN POWER TR. 26. WHAT ARE CHECKS IN POWER TR. DURING MAINTENANCE. 27. WHAT IS IMPORTANT WHEN WE CHECK OLTC OPERATION DURING MAINTENANCE. Trafo - Page 2 of 2
Is vtg is controlled by the resistor? if else how much?
what is the ckt diagram of a tubelight and is it the simplest ckt of electrical engineering and also the component?
