Interested to Buy Any Domain ? << Click Here >> for more details...
What is the difference between an axle and a shaft?
reply soon frnds........
- 11 Answers
- 40819 Views
- I also Faced
- E-Mail Answers
Answer Posted / samuel
Shafts are structural members mainly subjected to twisting
moment while axles are structural members subjected to
bending moment.
Shafts transmit angular motion from one member to other
while axles are static structural members supporting machine
parts in angular motion.
| Is This Answer Correct ? | 11 Yes | 7 No |
Post New Answer View All Answers
Preparation before arriving port?
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
In Turbine how the balence piston works and what is the direction of leak of steam flow.
what will be the min curvature ratio for Round Bar dia. 1” size in material grade AISI 4330, Yield strength 115KSI Tensile 140KSI?
composition of cast iron fc-500,fc-550,& fc-260 which is use in sheet metal industries as a piller set
What are the rules that must be kept in mind while designing castings?
Fire Engine should be stopped in auto mode or not. If stopped then why and if not then why not?
workingh principle of valve timing chart for cummins engine
What is viscosity and why is it important?
Hoew to represent unilateral tolerance, as Bilateral tolerance in engg drawing...? Example: 1.295 +0.000 and -0.10, as unitolerance, write the value in bilateral tolerance?
How do you define mechanical efficiency in case of compressor? How it is different that of an IC engine?
Where can you find thermometers in diesel engines?
Is cnc operating experience is must for successful career in cad/cam?How to make salary jump in this field of cad/cam?
. how will effect of water injection on turbine load and corresponding MW output(not water washing)
What are the causes if one cylinder in a diesel engine has a high temperature?
