write the formula for finding dimension of bearing from bearing number




Answer Posted / t.c.patil

Last two digit of bearing number shall be multiplied by 5
which is a shaft size.

Is This Answer Correct ?    330 Yes 85 No






Post New Answer       View All Answers


Please Help Members By Posting Answers For Below Questions

what is natural frequency & how to find it?

755


1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?

966


WHAT MADE YOU BECOME AN ELECTO-MECHANICAL ENGINEER?WHAT IS YOUR JOB DESCRIPTION?WHERE DO YOU WORK?WHAT ARE YOUR JOB RESPONSIBILITIES?WHAT IS YOUR WORK ENVIRONMENT LIKE?WHAT IS YOUR EDUCATIONAL BACKGROUND?WHAT COURSES DID YOU NEED OR ARE VALUABLE FOR YOUR POSITION?WHAT ARE THE ADVANTAGES OF YOUR JOB?WHAT ARE THE DISADVANTAGES?WHAT MADE YOU GO INT THE FIELD?HOW MUCH SCHOOLING DID YOU NEED?WHAT DID YOU NEED TO STUDY?

638


how to design a crankshaft?

1004


how gravity filling machine is designed

1234






Sir/Mam, I have applied for RRB chennai for the section engineer - mechanical posting. If any one is having the old written exam question papers please send it to my mail id : spramu@gmail.com Thanks in advance, Ramanathan...

853


What are reasons for poor machinability for IS 2062 steel

1423


Which questions will be asked for mechanical design Engineer position in GE?? plz give me reply it's urgent...

1401


whats the Formula to calculate temperature of steam at given pressure

571


which fit is this 177-S6?

846


present salary with all benefits (ctc) please give breakup it possible ?

1449


how to calculate the size and weight of induced draft axial fan impeller

244


What is the seal packing gland for turbine?

910


How would you increase the volume efficiency of centrifugal pump?

786


one kg of gas is compressed adiabatically from 1 kg/sq.cm,1 cubic metre volume and 300 kelvin to 5 kg/sq.cm,0.5 cubic metre and 400 kelvin.work transfer in this process will be

1907