Need to design filter...Length and diamter of shell
- 1 Answers
- 3194 Views
- I also Faced
- E-Mail Answers
Answer Posted / yash patel
Now i have posted all the required details .
Need to Design Filter .Where Polypropylene wound cartridge
to be fitted. Would you please help me carrying out the
design part. Especially length and Diameter of Shell.Please
help me out in performing calculations.Since i know now all
the basics .but one or the other hand its not getting solved
due to lack of knowledge.
If you don’t mind ,would you please solve it for my sake
once.
Type: Multiple Elements
Material Removed : PVC Particles
Design Data
Fluid Handled: VCM Vapor + Water Vapor
Flow M3/Hr Normal :318
Maximum:365
Density :2.67 kg/m3
Viscosity : 0.01
Operating Temp:54` C
Operating Pressure: 0.2 kg/cm2
Design Temp :170 `C
Design Pressure: 2.8 kg/cm2
Maximum Allowable Pressure Drop :0.01 kg/cm2
Desired Particle Retention, Filter Mesh to be Used:10
micron
MOC Shell: Carbon Steel
Filter Element: 304 SS
Inlet/Outlet Connections: 6 inch Flange
Vent/Drain Size :1 inch /3 inch
Line size : 6 inch
Clean Pressure drop across the filter: 0.006kg/cm2
Dirty Pressure drop across the filter: 0.02kg/cm2
Size of Filter Element:
ID : 30 mm
OD : 62 mm
Length : 750 mm
Where PP wound filter to be Fitted.
Please help me out.
Regards
Yash Patel
http://yashpatel.co.nr/
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
What are the strategies acquired to cure tube vibration and exchangers in a shell?
Explain how do you design a vapor-liquid separator or a flash drum?
Dear guys we adding hypo at climax plant and that water is inlet to DM plant so with hypo water that can affect my resins of cation and anion. if it is affect life of my anion and cation so what kind of steps should be take.
what is AZ431 & how to check it by using multimeter?
hai....i am chandrika. if anybody having test questions for HAL,HPCL,ONGC,IOL...PLS SEND THE QUES WITH SOLVED ANSWERS TO ME TO MY MAIL ID chandrismiles@yahoo.co.uk
Re: Sugar Cane Bagasse What are the 1. Specific Heat of Bagasse at 50% moisture, 40% moisture and 25% moisture? 2. What is bu;lk density of bagasse at 50% moisture, 40% moisture and 25% moisture? 3. What is specific gravity of bagasse at 50% moisture, 40% moisture and 25% moisture? 4. What is the specific heat of flue gases generated from boiler fuelled by bagasse? 5. What is the specific gravity of flue gases generated from boiler fuelled by bagasse?
How can wet carbon dioxide be responsible for a corrosion problem in iron-containing metals?
What chemical is used to expand air bags in such a short amount of time?
Hi, Please give me chemical engineering paper for IOCL exam for entire written exam, GD and personel interview model questions to my email id. (chemistnathan@rediffmail.com) Rgds, Ragu
What are some good strategies for curing tube vibration in shell and tube exchangers?
how will we calculate the heat of formation through electron...??
X is a solid having a white colour at room temperature. It has a density about 2g/cc. Although it has melting point near 325 degree Celsius, its properties start degrading above 260 degree Celsius. The coefficient of friction is very low about 0.1. It has very good dielectric properties especially at higher radio frequencies. It has a very high bulk resistivity. It is chemically inert. It is also resistant to van der Waals force. It is hydrophobic as well as lipophobic. Creep or ‘Cold Flow’ has been observed in X.
When an expansion is joint needed on the shell side of a shell and tube heat exchanger?
Is there a quick rule-of-thumb to estimate a gas side heat-transfer rate inside the tubes of a shell and tube heat exchanger?
Explain how are vessel lined with glass or how are they coated?
