Interested to Buy Any Domain ? << Click Here >> for more details...
what is the Excaste meaning of CT Saturation??
10 P 20, 15 VA, what is the meaning of 10, & 20.
if the CT polarrity changed what will happened??
what is the differece between measuring CT & Protection CT??
what is the Saturation Point of measuring CT & Protection CT??
- 1 Answers
- 11359 Views
- I also Faced
- E-Mail Answers
Answer Posted / ritesh ashok jaiswal
CT SATURATION MEAN CORE LOSS THE CAPACITY OF HOLDING THE
FLUX .THAT IS THERE IS NO OUTPUT AT CT SECONDARY .
15VA, class 10 P 10 CT means ratio error of prescribed
limit are constant up to 10 times rated primary current
when secondary burden is 15VA.
POLARITY CHANGE DEPENDS UPON FOR WHICH PURPOSE THE SAID CT
IS USED.
Measuring CT :-
 Use for measurement purpose.
 Accurate within the specified working range of
rated current (1% to 120% of rated current)
 Designed to saturate for more than 1.2 times
current to safe the measuring instrument from sever strain
caused by heavy over current.
 Accuracy is not required at high over current.
 High permeability core material with low saturation
level is most suitable ( Nickel- Iron Alloys).
b) Protective CT :-
 Use for protection purpose.
 A protective CT is required to faithfully transform
the primary current throughout it’s entire range from
normal load current to short circuit current.
 It should be accurate at all higher value of
current up to rated accuracy limit of primary current.
 To get high saturation level, grain oriented steel
are used for core.
GENERALLY the Saturation Point of measuring CT 30 VOLT &
Protection CT IS 300 V OR DEPENDS UPON MANUFACTURE TO
MANUFACTURE
| Is This Answer Correct ? | 6 Yes | 1 No |
Post New Answer View All Answers
Can you any one explain application of buccholz relay operation and pressure relif device operation of power transformer
How will you justify IR value and Charging voltage of any motor,transformer and Cables.......???? . . . . . . . . Plz tell me any body Baljeet Singh, engineer_89@refiff.com
What is maximum power transfer theorem?
How does HT work & Voltage required?
We have drive feeding an output contactor for a 5000 hp motor @ 5kV application. The motor FLA is 629amps x 1.25% service factor = 786.25 amps The cable that we current have in place between the drive and the output contactor is 350kcmil- MV-105 (parallel cables). Per the NEC table 310.60 (C) (69). This show the cable ampacity is at 615 amps per cable for a rating of 1230 amps. We have derated the cable for the cable tray and the multiple cables application and our calculations show that after the correction factor factor we are at 922amps. 1230 amps x .75% correction factor factor = 922.5 amps. The customer is driving us to then use another safety factor of .25% off of the already derated cable. Can you please provide a longhand calculation for your solution on this application?
how can we change the phase angle b/w two phase?
Why are cables rated for 40 KA for 0.25 Sec fault current rating?
How to calculate capacitor bank value to maintain unity power factor with some suitable example?
While converting delta into star or star into delta ,the three values of resistances remains unchanged .Find out the value?Let In star R1=x;r2=x;R3=x On converting into delta,R12=x;R23=x;R31=x Find the value of x
can any one tell me about the Extra low voltage systems?From where we give supply to these type of systems??
what is kvarh? Please define it With calculation General motors ?
why we change the direction of winding in rotor ?how we make the north and south pole?
The power supplied to a 33microF capacitor from a 120V, 60Hz source will be
WE ARE PLACE A NEW 75 KW MOTOR FOR JPF.IT IS CONNECTED IN M.C.C. WHEN WE ARE STARTING M.C.C.INCOMER IS TRIPPED.THEN WE ARE CONNECTED IN P.C.C WITH A MM30 RELAY PROTECTION THEN WE ARE STARTED MOTOR WILL RUN SMOOTHLY.
after how many spot we must chang secondry cable in portable spot welding gun?
